Question about 2001 Suzuki Esteem

1 Answer

HID headlights for esteem

Can i fit hid headlights in my esteem, hw much they wud cost & where can i get them in India?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

There are retrofit kits for your car, but they're expensive. If you're needing better headlights I would look for a aftermarket high wattage halogen bulb. If you just want the cool look then Sylvania Silverstar bulbs are the closest low cost alternative. They're not the same as HID but they're close at a fraction of the cost. As far as HID in India, your best bet is looking on the Internet. Most HID kits that would fit your car are 200 to 400 dollars US. Good luck and don't forget to vote

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing halo and hid lighting in an after market headlight


    Aftermarket Projector Headlight How To Replace HID ...

    store.ijdmtoy.com/Aftermarket-Projector-Headlight-HID-Installation.../5...
    Here are some quick tips and instructions on how to install an aftermarket HIDConversion kit into an aftermarket projector headlight assembly. ... Aftermarket projector headlights look almost like an OEM headlight with the exception of the wiring and design. You would need to remove ... images for Replacing halo and hid lighting in an ...

Nov 24, 2015 | 2000 Jeep Grand Cherokee

1 Answer

Headlights do not work high or low beam all other lights work


Re: Condensation in Sienna Right Headlight.... - Toyota Sienna Forum

www.siennachat.com/.../4606-condensation-sienna-right-headlight.html
Mar 10, 2009 - 15 posts - ‎9 authors Over the years, I was not a frequent visitor to SiennaClub...but when I did visit, it was... in the right, passenger-side xenon HID headlight of my 2004 Sienna...the light has... Check with your dealer and see if they can do anything about it. .... :o The HID bulb is also a PITA to remove because you are working ... Re: 2004 Sienna no brake lights, radio, heater/AC ...
15 posts
Jan 4, 2013
Thread: HELP: Both Low Beams don't Work
6 posts
Nov 27, 2011
Thread: 2000 sienna drl and/or headlight issue
5 posts
May 7, 2010
Automatic Headlight Option: Useful or Not?
8 posts
Mar 3, 2010
More results from www.siennachat.com

Toyota 2004 Sienna repair: Replacing HID ballast or ...

toyotarepairsemipro.blogspot.com/.../replacing-hid-ballast-or-computer....
May 1, 2010 - Replacing HID ballast or computer control lighting for the Headlight. Just got a ... Up until now, I did not know I had the option of seeing twice as far with Xenon. Also up to ... In the end after buttoning everything up, the light did work fine. .... Howdo you determine if you have a HID or non-HID light? Reply ...

Oct 15, 2015 | 2004 Toyota Sienna

1 Answer

Hid headlights


( please add year and model type) you just need to change the module for the hids usually fitted to the light housing. they dont cost alot to replace. but converting back to normal lights you will need the the light bulb housing. these can be hard to find. as they just get chucked away. you can get hid kit if you want to change both lights they come with a manual on how to install them.

Mar 16, 2014 | Mini Cars & Trucks

1 Answer

Hid headlight on 2005 vw beetle won't work


For many European cars, you might need to add capacitor to ensure the HID working properly.

You will probably need this

CAN BUS Error Free HID Decoders Installing HID Conversion Kit

Jan 27, 2014 | Cars & Trucks

1 Answer

Fitted hid headlights now driving lights dont work


The problem with HID lights is that they require 12 volts or more to work. Daytime running lights on require 6-9 volts from the module. So when the original lights are replaced, the daytime running lights will not supply enough voltage to the HID ballasts to turn them on. The result? No Daytime Running lights. Another alternative is to purchase LED strips and place them around your headlights with a fused accessory power from the ignition switch. When the car is on the strips light up and you have Daytime Running Lights!

Jun 20, 2012 | Cars & Trucks

2 Answers

How to install hid on a bmw 325xi 2006


INSTALLATION GUIDE:
BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
Parts Identification:
Projector Headlight
Halo & L.E.D.
Bottom of the Headlight:
Ballast Bracket, Halo Wires(red/black)
Turn Signal Adaptor
TOOLS REQUIRE
10mm - 8mm socket
Philip Screwdriver
Crimper/Pliers
For more information about how to install your vehicle, come visit our youtube page on
http://www.youtube.com/spyderauto
Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
STEP:
Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
Factory Xenon Headlight
Spyder Projector Headlight using Factory Xenon Lights
STEP:
pls vote an diam giving you link also for better help BMW e46 HID Headlight Replace
install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-0.jpg

install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Oct 15, 2009 | 2003 BMW 325

3 Answers

I replaced my main bulbs with hid xenon in my 98 range rover hse


First let me just explain something about putting HID bulbs in a reflector headlight, then I'll get to answering your question. High end cars use something called a projector with their HID bulbs and these projectors focus the light into patterns that won't blind other drivers with very perfect cutoffs (no light goes above a certain line). To retrofit a projector into your stock housing it takes a lot of work and careful measurements and thus a lot of time. But this is the only way to do a HID retrofit the right way.
Putting a HID kit into a reflector housing as you did, also makes light scatter everywhere, which creates many hotspots or high concentrations of light that make it much more difficult to see the road. Not only do HID kits in relfector housings make it more difficult to see, they are hugely illegal, and can/may get you pulled over and ticketed by a police officer. 
The best thing you could do insted of putting a HID kit in your relfector housing is to get higher wattage bulbs, OSRAM makes some great H4 overwattage bulbs. http://www.rallylights.com/SearchResult.aspx?CategoryID=6
If you purchase from rally lights (you need to purchase them in sets of two( I wouldn't go over 85/80 watt bulbs because it could melt your housing.)
Also make sure your headlights with stock bulbs are aligned correctly, most of the time this alone makes a huge difference as headlights droop over the years. 
If you are set on using your HID Kit illegally and blinding all other drivers on the road and willing to live with the risk of getting pulled over by any cop you run into. You will need to figure out how to trick ecu into thinking regular headlights are being used because its detecting the power being drawn for your HID lights to be a fault in the system that needs to be replaced. You can do this by wiring in a 55watt resistor to the circuit. 

May 18, 2009 | 1998 Land Rover Range Rover

3 Answers

HID fog light


check your connections to the relay, sounds like something is breaking down under load

Feb 18, 2009 | 2005 Chevrolet Silverado

1 Answer

The Metal Hook can't fit back into its hook after installing a H4 HID bulb


You could try removing the metal retainer(long metal balde) in an old wiper blade and forming it into shape to hold the bulb...I've done one honda HID retainer with it and it works...You need to have a good pair of pliers and a side cutter to cut the metal as it is very hard and like a spirng.
Good luck.

Nov 10, 2008 | 2000 Honda Civic

Not finding what you are looking for?
2001 Suzuki Esteem Logo

Related Topics:

505 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...