Question about 2004 Ford Explorer

1 Answer

Air Conditioned Seat Not Working

2004 Expedition Eddie B. Hit the button for A/C or Heat on my drivers Seat and the button illuminates for about 5 seconds and then shuts off. Won't turn again unless the truck is shut off and restarted. I hear the click like it's going to turn on, but no go. The passenger side works fine. I have the same proplem on 2004 sport trac the heated seat on driver side. the switch lights up but no heat, the book does not segregate the heat on the seats so what fuse do you check ?

Posted by on

  • gary7887 Feb 21, 2009

    2004 ford f 250 problem with heated seats the light on but no heat

  • Anonymous Mar 22, 2014

    drivers side heated seat will come on and stay on for a few minutes and then shut off; it will not come back on unless you shut off the engine and restart

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

Check the rail system on the seat. sometimes it pulls the wire out and it doesn't get good enough connection

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Buick Lucerne CXL: Cooled seats not working. LIghts come on, temperature adjusters work but the motors under the seats do not come on.


Air Circulation
When the heated/cool seat switch is pressed to initiate operation of the climate control seat (CCS) system, cabin air is drawn through the heated/cool ventilation module air filter, then directed through passages in the foam of the seat cushion and seat back to the seat's occupant. In order for the CCS system to operate to its optimum performance, it is crucial to have unrestricted air flow through the system. A dirty or restricted air filter, the blockage of an exhaust air duct, a misaligned heated/cool ventilation module, or incorrect foam installation of the seat cushion or seat back will all have negative effects on CCS operation.
Heated/Cool Ventilation Module
Each heated/cool seat has 2 ventilation modules, one located under the seat cushion and one located in the seat back. These modules are controlled by the climate control seat module (CCSM). Each ventilation module contains a thermo-electric device (TED), a temperature sensor, and a blower motor. The TED and temperature sensor are mounted downstream of the blower motor. Each TED consists of a circuit of positive and negative connections sandwiched between 2 ceramic plates. Each ceramic plate is equipped with copper fins for heat exchange. The air flowing past these fins is either directed as conditioned air into the seat cushion and seat back, or directed into the cabin as waste air.
A TED is essentially a solid state heat pump that is used to heat or cool the air supply to the seat cushion and seat back. When voltage is applied to a TED, one side releases energy as heat, while the opposite side absorbs energy and gets cold. When the polarity of the current flow to the TEDs is switched, the hot and cool sides of the TED reverse.
During the following climate control seat system description and operation, the TEDs, blower motors, and temperature sensors will be referenced independently even though they are all packaged together as a module.
Climate Control Seat (CCS) System
The CCS system consists of two heated/cool ventilation modules and one climate control seat module (CCSM) that controls both the driver and passenger heated/cool seats systems. The CCSM is mounted below the front passenger seat cushion. It receives power from both, battery positive voltage and ignition 3 voltage.
Once a CCS system is activated, cabin air is drawn through the seat blower motors and directed across the fins of each of the thermo-electric device (TED) located under the seat cushion and in the seat back. The air is either heated or cooled as it passes over the TEDs. This conditioned air is then directed through channels in the foam of the seat pad and through small holes in the seat cover to the occupant. Once the system is activated, the CCSM uses a set of algorithms to control the temperature of the selected heating or cooling modes.
Your best bet is to take your vehicle to a qualified repair shop an have it diagnosed .
DTC B19A4: Driver Seat Back Blower Speed Circuit High

DTC B19A8: Driver Seat Back Blower Speed Circuit Short to Ground

DTC B103D: Driver Blower Power Circuit

DTC B272E: Driver Seat Back Blower Circuit Open
DTC B19A3: Driver Seat Cushion Blower Speed Circuit High

DTC B19A7: Driver Seat Cushion Blower Speed Circuit Short to Ground

DTC B2729: Driver Seat Cushion Over Temperature
DTC B19A2: Passenger Seat Back Blower Speed Circuit High

DTC B19A6: Passenger Seat Back Blower Speed Circuit Short to Ground

DTC B111D: Passenger Blower Power Circuit

DTC B272F: Passenger Seat Back Blower Circuit Open
DTC B19A1: Passenger Seat Cushion Blower Speed Circuit High

DTC B19A5: Passenger Seat Cushion Blower Speed Circuit Short to Ground

DTC B272A: Passenger Seat Cushion Over Temperature
Driver and Passenger Heated/Cool Seats Inoperative
  1. Ignition OFF, disconnect the C1 harness connector at the CCSM.
  2. Test for less than 5 ohms between the ground circuit terminal M and ground.
  3. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  4. Verify that a test lamp illuminates between the B+ circuit terminal E and ground.
  5. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

  6. Disconnect the C2 harness connector at the CCSM.
  7. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  9. If all circuits test normal, replace the CCSM.


Sorry

Jul 10, 2016 | 2007 Buick Lucerne CXS Sedan

1 Answer

Heated seat not working on 2000 ford expedition eddie bauer


Check continuity on the seat heaters. If that's ok, check the grounds. Check power to the heaters while you are there.

Dec 01, 2013 | Ford Expedition Cars & Trucks

1 Answer

Clicking noise right rear by third seat 2004 eddie bauer expedition when rear heat and air on or car on


I had the same problem with 2004 Expedition. Changed the actuator for the blend door. This is the one that determines the air temp (cold ---- hot). Purchased Actuator from Advance Auto Parts and installed. I was able to install this pulling out on panel, but it's tight and you will have limited movement and sight. It started clicking again in about a year. After reading other solutions, I realize my Blend Door may be hanging at times. It currently only clicks on coldest setting. If it's moved off of cold a little the clicking will stop. I have also noticed if the setting is not moved in just the spot and you use other electrical current such as windows or brakes it will click because of voltage change and will need adjusting more. I have to adjust this setting in the front if set on front controls as well as the rear if set for rear control. It works fine on Warm or Hot setting. I plan to check door binding when I have time. Good Luck

Nov 22, 2012 | 2004 Ford Expedition

1 Answer

Does Ford 2004 Eddie Bauer Expedition have carburetor?


it is very possible that it is a idle air control motor.it is located in the intake

Jul 04, 2012 | 2004 Ford Expedition

1 Answer

I have an 2004 Ford Expedition Eddie Baurer, Check Air Suspension light is on. The suspension is not working at all truck rides very low and bounces every time a bump is hit, what could be wrong?


Any part of the air ride suspension system could have failed.
I would replace the air suspension, with a conversion, such as strutmaster or similar product,other wise you have to diagnose your current system and repair.

Oct 04, 2010 | 2004 Ford Expedition

1 Answer

A 2004 Ford Expedition Eddie Bauer driver side window not working


The entire assy. This uses a cable system and what you are hearing is the cable twisting and getting ready to snap. New units are available at Advance Auto parts

Jan 14, 2010 | 2004 Ford Expedition

1 Answer

Heat light switch comes on..but the heated seat is


MORE THAN LIKELY THE HEATING ELEMENT HAS MALFUNTIONED. ITS A PRETTY COMMON PROBLEM IN HEATED SEATS

Nov 29, 2009 | 2003 Ford Expedition

5 Answers

Air Conditioned Seat Not Working


it seem like an electric issue. check and confirm all the fuse are intact

Sep 22, 2008 | 2004 Ford Expedition

Not finding what you are looking for?
2004 Ford Explorer Logo

555 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...