Question about Ford Escape

Open Question

How do you repla broken bolt on braket to hold hanger bearing support on 2006 ford hybrid awd

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rpower
  • 11 Answers

SOURCE: 3 broken bolts for tire

Typically, you'll have to remove the caliper and brake rotor. Then, remove the wheel assembly form the axle and use a press to force out the broken stud. Unless you have access to the proper tools to do this, you would probably be better off having a mechanic do it- The shop near me charges about $16 to replace a broken stud and even though I can do it myself, for as much of a pain that it is to do, I'd rather just pay them to do it.

Posted on Jul 19, 2008

ourhowse
  • 2007 Answers

SOURCE: removal of axle 1997 ford explorer awd

You have to take the rear differential apart, and then pull the axle.

Posted on May 05, 2009

  • 161 Answers

SOURCE: replacing the rear wheel bearings on buick rendezous

most likely, the instructions would tell you to get the swaybar off first. double check the instructions at the library.

Posted on Jun 14, 2009

  • 100 Answers

SOURCE: Need to change hanger bearing on 2006 model toyota

You have to remove the driveshaft (Both halves) then let a pro replace the bearing itself
reinstall and that's all there is to it

Posted on Sep 13, 2009

gladys_neal
  • 334 Answers

SOURCE: 2005 ford escape 3.0l AWD XLT - DRIVESHAFT CARRIER

if there is some one in your area that balances driveshafts they can change just the bearing for you

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 escape AWD, replace front hub bearing


Rather than just the bearing, I suggest a new half shaft as the bearings and ABS tone wheel are already assembled. These Escapes are notorious for cracking the tone wheel setting off a code and then disabling the AWD system. So for a very few dollars more than it would take to disassemble the shaft , install bearings and tone wheel just get a new one.

Jun 09, 2014 | 2006 Ford Escape

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626


This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

1 Answer

Rear wheel bearings


I am not familiar with this car, but maybe you need a

hydraulic press

Mar 28, 2013 | 2006 Ford Escape

1 Answer

Ford escape 2006 awd driveshaft carrier bearing stud replace


if flush break than drill and use a remover can buy a remover at most hardware-home-auto stores ====if their is enough to grab stud use heat carefully and a stud tool -vice grip or anything that will grab the stud to remove it

Jan 12, 2013 | 2006 Ford Escape Hybrid

3 Answers

I need to remove my front axel on my 1989 toyota camry


Jack up car and apply e-brake. car will roll if one of the front tires leaves the ground. remove tire , spindal nut and lower ball joint bolts. remove axle from hub then use a prybar to pop it out of trans. the passenger side will have a braket holding axle to engine , remove bolts from braket or squeeze snap-ring to rmove axle from braket.

Jan 11, 2011 | 1989 Toyota Camry

1 Answer

I need to pull the drivers side front axel off how do i do it


remove axle
1. remove wheel
2. remove brake caliper and brake braket
3. remove rotor
4. remove 4WD locking hub
5. remove c clip on axle
5a. (leave wheel bearing assy on after taking c-lip off saves time unless you want to take it of in that case you have 4 bolts on the backside of the bear that you will have to unbolt)
6. unbolt upper and lower ball joints
7. use ball joint tool and seperate
7a. remove spindel knuckel
8. slide axle out

Aug 28, 2010 | 2006 Ford F-250 Super Duty

1 Answer

Drivers side wheel bearing what do i need to do to replace it myself


Front - Remove tire, then remove brake caliper and caliper braket, remove brake rotor, some times will have little clips, remove clips, if they break ok, won't used them again, if 4X4 remove center axle nut, disconnect ABS harness, on back side of bearing, there will be three bolt's that hold hub bearing assembly, remove bolts, bearing should slide out, some time with a little help from a hammer, and your done , reverse to install new hub bearing assembly, just make sure that ABS harness is in same location that old one was when putting bearing in.

Jul 21, 2010 | 2004 Mercury Mountaineer

1 Answer

The axle pops out on my 98 ford contor


If its the passenger side axle then the hanger bearing retainer may be missing the bolts, or rusted out and not holding it in place. Check ! Make sure that the outer shafts are not missing the nuts that hold them to the wheel, and check your lower ball joints for integrity.

Jan 28, 2010 | 1998 Ford Contour

1 Answer

Changeing front bearing hubs


remove the tire, then remove the brake caliper and its braket then slide rotor off. next is to remove the center axle nut, now look on the backside, you will see the bolts that hold bearing asm, in place remove bolts and hub comes off, you may have to beat hub with a hammer to break free, note if you have abs system disconnect connector before removing hub. reverse directions to install.

Jan 19, 2010 | 2003 Chevrolet Impala

1 Answer

How to remove rear shocks in my 1997 ford eplorer


There should be 2 bolts in a bow-tie shaped braket on the top of the shock, with a nut on the other side, through the frame. There should be one large bolt and nut on the bottom of the shock, through a braket on the rear axle.

Lift the vehicle up by the frame on both sides, so that the axle is dangling underneath the vehicle, and the shocks should be very easy to remove and reinstall.

Nov 20, 2009 | 1997 Ford Explorer AWD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...