Question about 2006 Ford Escape Hybrid

Open Question

How to replace braket #yl8z4a499aa

How to replace broken bolt on braket #yl8z4a499aa to hol hanger bearing support

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
BCAS1298
  • 3092 Answers

SOURCE: Hanger bearing needs to be replaced and a axle

The carrier bearing for the axle will come with new 1/2 shaft.

Posted on Jul 22, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace front wheel bearing on 2009 dodge journey?


REMOVE TIRE CALIPER CALIPER BRAKET BRAKE DISK THEN REMOVE CENTER NUT FOR THE U JOIN AND REMOVE THE BOLT FOR THE HUB ASSY AND REMOVE HUB

Oct 05, 2014 | Cars & Trucks

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626


This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

1 Answer

Replacment of left front wheel bearing


That is not that hard to do ! first lift car take wheel off then take the caliper off and brakes ,braket that stops rotor from coming off then take rotor off then take spindle nut off and behind bearing you will see 3 bolts take them off bearing should come loose then get a hammer and start pounding then when it comes off clean the inside of hole that holds bearing with wire brush then grease it and grease spindle then you just have to reverse steps.......

Jun 18, 2011 | 1998 Kia Sephia

3 Answers

I need to remove my front axel on my 1989 toyota camry


Jack up car and apply e-brake. car will roll if one of the front tires leaves the ground. remove tire , spindal nut and lower ball joint bolts. remove axle from hub then use a prybar to pop it out of trans. the passenger side will have a braket holding axle to engine , remove bolts from braket or squeeze snap-ring to rmove axle from braket.

Jan 11, 2011 | 1989 Toyota Camry

1 Answer

How replace front wheel bearing


remove wheel,brakes,an caliper hanger the hard part is to remove the king nut or axle nut after u get that remove bolts on back of spendle remove hub or bearing assembly replacewith new one repeat steps in reverse

Dec 20, 2010 | 1996 Toyota Celica

1 Answer

Drivers side wheel bearing what do i need to do to replace it myself


Front - Remove tire, then remove brake caliper and caliper braket, remove brake rotor, some times will have little clips, remove clips, if they break ok, won't used them again, if 4X4 remove center axle nut, disconnect ABS harness, on back side of bearing, there will be three bolt's that hold hub bearing assembly, remove bolts, bearing should slide out, some time with a little help from a hammer, and your done , reverse to install new hub bearing assembly, just make sure that ABS harness is in same location that old one was when putting bearing in.

Jul 21, 2010 | 2004 Mercury Mountaineer

1 Answer

How do I change the front wheel bearing in a 2001 Sonata 6 cyl


jack the front off the ground remove the tire remove the brake caliper remove the rotor remove the bolt hol;ding the front axle into the spindle hub, remove the hub and bearing.

May 06, 2010 | 2001 Hyundai Sonata

1 Answer

Is it hard to replace hub bearing on gmc jimmy 2001


No,,,Remove the wheel,the brake caliper,unplug the abs sensor,if it is 4x4,rmove the center nut on the axle,rmove the rotor,and caliper braket,bracket first of course,then unbolt the three bolts that hold the bearing assembely,that is it.

Mar 25, 2010 | 2001 GMC Jimmy

1 Answer

Changeing front bearing hubs


remove the tire, then remove the brake caliper and its braket then slide rotor off. next is to remove the center axle nut, now look on the backside, you will see the bolts that hold bearing asm, in place remove bolts and hub comes off, you may have to beat hub with a hammer to break free, note if you have abs system disconnect connector before removing hub. reverse directions to install.

Jan 19, 2010 | 2003 Chevrolet Impala

1 Answer

How do I replace a 2005 Pontiac Grand Prix front wheel bearing. Do I need a press?


no its a bolt on, must remove wheel brake caliper and its braket then brake rotor, look at back of spindle you will see 3 bolts ,remove them and hit frt of hub until it comes out . good luck.

Oct 20, 2009 | 2005 Pontiac Grand Prix

Not finding what you are looking for?
2006 Ford Escape Hybrid Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...