Question about 1990 Chrysler TC

1 Answer

No brakes repair shop tells me brake booster pump and master cylender need replacement....where can i get parts the brake pump does not work

Posted by on

  • guidomut Jan 31, 2009

    i have a 89 with the same problem. did you get any help?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Any Auto Parts Store Should Carry thes Parts. There are Pretty Common Parts. Please Rate my Response. I need all the Help that I can get! Thanks!

Posted on Jan 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do u change the brake booster on a 99 Monte carlo

Hi Michelle, Im AL the owner of Big As Auto Repair.

This is an easy task with the correct tools.

First, pump the brakes 20 times with the key off. Next, remove the 2 nuts that hold the master cylinder in place. Next, pull the master cylinder back and out of the brake booster. Next, go inside the vehicle and on the brake pedal arm you see the brake booster rod attached to the brake pedal arm by a retainer clip. Next, remove the clip and slide the rod away from the pedal arm. Next, around the brake booster rod at the firewall you'll see 4 nuts you'll need to remove those 4 nuts then push the booster backward out of the firewall. Next, go back under the hood and pull the booster past the master cylinder. NOTE: You should have enough room to force the booster past the master cylinder. Replace the new booster and hook up the vacuum hose and your done. Hope this helps and please visit my auto-repair-website here:

Dec 11, 2015 | Cars & Trucks

1 Answer

Brakes not working

A regenerative brake is an energy recovery mechanism which slows a vehicle by converting its kinetic energy into another form, which can be either used immediately or stored until needed. --------------------------------------------------------------------------------------
Benz MB STAR compact C4

Feb 19, 2013 | 1998 Ford Windstar

1 Answer

Brake pedal will not depress.

indicates that it is the booster or second ,a faulty brake master cylinder
boosters can be repaired for considerably less than that or get a good unit from the wreckers /junk yards
get a second opinion from an accredited brake specialist shop

Jul 11, 2017 | 2010 Subaru Forester

2 Answers

03 F150 spongey brakes after replaceing brake cylender and bleeding brakes?

This sounds like a bad brake line, these trucks are famous for rotted lines behind gas tank, make sure there are no leaks, this sounds like a leak or a defective master cylinder, if this is the same problem then i would say it is a line also check the rear brakes for leaking wheel cylinders unless you have rear disc brakes, check calipers for leaks.

Take a good look at brake system for leaks, hold brake pedal a few times and let is sink to floor , do it about ten times and then look for a leak, good day

Jun 24, 2012 | 2003 Ford F150 Regular Cab

2 Answers

Delica L300 4x4 brake problem

Replace master cylinder, do not use kit, master cylinder bores are probably scored.

Nov 20, 2017 | Pontiac Cars & Trucks

1 Answer


sounds to me that your power booster is not holding pressure

Dec 25, 2011 | 1986 Ford F150 SuperCab

2 Answers

I am working on a 1993 f-350 with a 7.3 diesel the truck came to me with the brake pedal going to the floor... the customer had already put 3 new master cylenders on it along with a new brake booster......

I would ask where you got the master cylinders from. Were they new, or rebuilt? If the front brake pads look good and no apparent problems from the calipers, it can only be 2 problems. First, is there a leak somewhere in the system. If you have confirmed that there is none, then the master cylinder is 'bleeding' from front to back. Air wouldn't be a problem as you seem to have bled the brakes well, but the only sure way to know is using a bleeder. They run from a simple hand vacuum device to an air powered device which forces brake fluid thru the system.
Since your 'customer' replaced the booster, make sure the plunger rod is set correctly. Perhaps it is not set at the correct length, in which case you will never get a pedal. Diagnosis for this is a pressure tester to see if any pressure is being generated by the calipers.
Good luck. Hope this helps.

Sep 22, 2011 | 1993 Ford F350

1 Answer

Brakes will not bleed and stay up

Make sure bleeder fittings are on the top side of the front caliper,have seen them insatlled wrong left to right before & cause this problem.Also if you have ABS the abs modulator has to be bled also,there are bleeders on the unit.hope this helps

May 21, 2009 | 1994 Saturn Sl

2 Answers

My 1994 buick lesabre's brakes will not work. I have low brake fluid and the brake pads were just replaced. My friend said that there was brake fluid leaking from the car and that I might need a master...

if you can see a good amount of wet brake fluid between the brake master cylinder and the brake booster. and you have been adding fliud often,you could have a bad master cylinder. it has to be replaced not rebuilt. you however may have a far more common problem, a rusted through brake line.have someone pump the brake pedal, than look under the car for a brake fluid leak ,repair as needed. than bleed the brakes for a good hard brake pedal
good luck chris

Mar 18, 2009 | 1993 Buick LeSabre

2 Answers

No brake pedal

the only thing i can think of is you brake master cylender

Aug 17, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
1990 Chrysler TC Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides