Question about Chevrolet Silverado 1500

Open Question

My headlights on my 2004 gmc sierra shine too low how can i adjust them up?

My low beam lights shine too low i have top turn on my high beams to see normal for low beams

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: no driving or high beam headlights

Hi,

To my knowledge a 2003 Toyota Camry uses a dual filament halogen bulb, either by Osram, Philips or Sylavania. If on the dashboard, the blue indicator lits when the switch is moved to bright or the passlight is engaged but no headlight, then it could jut be busted bulb (or part of it since you still have driving/low beam). In some cases, it could be the relay that supplies power direct to the bulb. At other times, it could be fuse(s) assigned to high beam. At certain instances, it could be also a loose, corroded or burned connector.

Corrective measure for your concern would be to check the 2 bulbs. This is performed by removing the rear covering (rubber or plastic cap) of the headlight assembly from the rear. The bulbs are held in place by a spring clip that needs to be unlatched from the base/holder. Carefully remove the bulb taking care not to touch the glass envelope. The filaments would be readily visible and cut/breaks would be apparent. If determined that one of the filaments (high beam) is open, replace the bulb(s).

If the bulbs prove to be OK, you need to work yourself backwards tracing the wiring harness. After the bulb, check the 3 prong connector for any corrosion or scorching/burnt marks; clean as maybe required. Next to check would be the relay that provides the +12VDC and then the fuse.

I doubt if the dashboard or steering wheel components involve with headlights may be at fault.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Jun 02, 2008

  • 193 Answers

SOURCE: high beams wont turn on.

First place to start is with headlight switch. I did have a case many years ago when both high beams were blown out at once, but this is rare. When you have the headlight switch out, jump power from te low beams to the high beam contacts. If high beams come on, replace switch.
Bill

Posted on Nov 19, 2008

  • 1 Answer

SOURCE: low beam headlights not working on 2004 Pontiac Montana extended

You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.

I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp

Posted on Jan 06, 2009

  • 840 Answers

SOURCE: Adjusting the low beam headlight

its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

Posted on Jan 31, 2009

  • 1986 Answers

SOURCE: HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust headlight beam on my 1996 GMC Seirra pickup


just above head light there is adjustment screws

Mar 04, 2016 | 1996 GMC Sierra

1 Answer

1998 GMC Sierra has running lights and high beams but no low beams. Headlight switch is not the problem


first off, be sure your low beams aren't both burned out. it happens all the time. next check your dimmer switch operation. (i'm betting on low beams burned out) good luck.

Dec 21, 2010 | 1998 GMC Sierra

1 Answer

Does this model use a 4 headlight bright system? I have 2 low beam lights but when I put on the bright lights the 2 low beam lights go out and only the 2 bright lights stay on.


I think that many 1990s and even some 1980s GM vehicles with seemingly 4 headlight systems actually use only 2 at a time.

My 1990 Oldsmobile Cutlass Calais, for instance, had 2 high beams that went on independently of the 2 low beam lights when switched with the turn signal lever.

In the 1970s the GM vehicles had 4 headlight systems where all 4 headlights would go on, but they used sealed beams rather than the capsule lights that are used nowadays.

For instance, our 1976 Cadillac Seville has a 4 headlight system that lights up 4 headlights on the high beam mode.

Good luck on seeing at night with the current set up.

Dec 09, 2010 | 1992 GMC Sierra

5 Answers

How do i adjust my headlingt on a 2001 suzuki xl7


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 14, 2009 | 2001 Suzuki Xl 7

2 Answers

How do I adjust the headlights to see further down the road on my 2004 Chrysler Pacifica?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 12, 2009 | 2004 Chrysler Pacifica

1 Answer

HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 06, 2009 | 2001 Hyundai Tiburon

2 Answers

Headlamps need adjustmentthey shine to close to the car even when on high beeam


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 30, 2009 | 2004 Saturn ION

2 Answers

Can't adjust the height of the headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 13, 2009 | 2004 Audi TT

1 Answer

My GMC truck 1993 Sierra just had new headlights installed. But the high beams point into the trees. It seems both the high and low beam lights are in one enclosure. Can I adjust these down?


Yes you can. There is an adjustment screw at the top of each head lamp and you just turn them out or counter clockwise and the beam will come down. You may also have to adjust them side to side also. There is an adjustment screw as well.

Aug 27, 2009 | 1993 GMC Sierra K1500

1 Answer

Headlamps for a 2006 gmc sierra aren' t working


i would try replacing headlight switch....

Jun 08, 2008 | 2006 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...