Question about Cars & Trucks

Open Question

I bought the HOZEMATE RETRACTABLE HOSE REEL WITH 16 mm for garden. Where can i buy 16mm hose fitting. All the hardware out let only have 12mm and 18mm hose fitting only. Many thanks!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: coolant leak at the top radiator hose

the plastic radiator tank that the hose nipple is part of can be replaced by any radiator repair shot for about $75-100

Posted on Apr 06, 2009

Ad
co7196
  • 3433 Answers

SOURCE: 2001 dodge ram 1500 4x4 vent hose on rear axel

The hose is only an extension to elevate the vent. Trucks have these so they can be braver about crossing axle deep water.. The plastic piece on the end is somewhat of a chk valve so the hose isn't open to dirt and road spray.It should be cliped to the frame to stay elevated.

Posted on Jun 08, 2009

ronaldo_ross
  • 1056 Answers

SOURCE: I'm trying to recharge the A/C in my 04 PT

The low side connectors are diffrent from the high side, you would not be able to connect it anyways. The high side has a bigger port that the low side, and it would not fit anyways.

Posted on Aug 04, 2009

SOURCE: 99 gmc heater core inlet hose plastic fitting broke

Buy the correct tool

Posted on Sep 28, 2009

  • 1 Answer

SOURCE: 99 Chevy Z71 heater core inlet hose male fitting broke

This is an easy $7.00 fix. Go to your local auto parts store and get a GM Heater Hose Fitting. I went to NAPA, part #730-5631. Cut of the old fiting with a hack saw blade, being careful not to damage the pipe from the heater core, put the new one on. Total time takes less than 10 minutes, make sure you fill your coolant resevoir.

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix a frontgate Vector retractable hose reel


possibly the spring inside has broken off .

Sep 20, 2017 | Vector Cars & Trucks

2 Answers

Can you fix broken hose connection without buying whole hose?


are you talking garden hose or what?
if a garden hose ,just cut the end off and get fittings from your local hardware shop

Nov 22, 2015 | Cars & Trucks

2 Answers

12mm to inches in a spannans


7/16 or 1/2 closest, especially if 6 point

Feb 23, 2015 | Cars & Trucks

1 Answer

What size is the lower ball joint lug of a 2000 lincoln ls, 14mm or 16mm


16 mm. there is also a 1/2 year model with an 18mm look on the driver door where the latch is and see if your car was produced in may or june if so it is a half year model therefore it will be an 18 mm

Jan 02, 2013 | Cars & Trucks

1 Answer

How do I remove my car radiator?


Section 303-03: Cooling, Engine 1997 Explorer, Mountaineer Workshop Manual REMOVAL AND INSTALLATION Radiator - 4.0L Removal
  1. NOTE: Refer to following illustrations.
    Drain the cooling system by removing the radiator cap (8100) and attaching a 9.5 mm (3/8 inch) inside diameter hose to the draincock nipple, located at the lower rear corner of the radiator tank. Then, open the radiator draincock (8115) and allow the coolant to flow through the hose into a suitable container.
  1. Loosen hose clamps at throttle body and engine air cleaner assembly. Remove air cleaner outlet tube and position aside.
  1. Remove radiator overflow hose from the radiator, disconnect two hose locators at top of radiator and position hose aside.
  1. Remove two fans shroud bolts. Lift the fan shroud out of the lower retaining clips and position it on the fan blade.
  1. Position upper and lower radiator hose clamps, remove hose from radiator and position it on the fan blade.
  1. Disconnect the two transmission cooling lines from the oil cooler fittings on the radiator, install protective caps over lines and position aside.
  1. Remove two upper radiator bolts.
  1. Tilt the radiator back (rearward) approximately 25 mm (one inch) and lift directly upward, clear of the radiator support bracket and the fan blade.
Installation
  1. Position the radiator into engine compartments, make sure that mountings on both tanks are inserted into radiator support brackets. Install radiator retaining bolts. Tighten to 6-8 - (54-70 lb-in).
  1. Remove protective caps from cooler lines. Connect the two transmission cooling lines at the oil cooler fittings on radiator. Tighten to 16-24 - (12-17 lb-ft).
  1. Install upper radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Install lower radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Position fan shroud in lower retaining clips and install upper bolts. Torque to 6-8 - (54-70 lb-in).
  1. Position radiator overflow hose, connect to radiator and locators.
  1. Position air cleaner outlet tube to throttle body and air cleaner assembly. Tighten to 2-3 - (18-27 lb-in).
  1. Fill the cooling system; refer to Cooling System Draining, Filling and Bleeding in this section.

Oct 28, 2010 | 1997 Mercury Mountaineer

1 Answer

How do u replace the power sterring hose in a 2000 oldsmobile intrigue


You need a 16mm flare nut wrench - they sell them at Autozone. Buy two. Usually it is the high side that leaks - remove the fitting at the pump and at the rack. To get to the fitting at the pump you might want to fabricate your own wrench with a torch:

e18efcc.jpg
To get to the fitting at the rack you will want to remove the sway bar and drop the rear two bolts on the engine/ drivetrain cradle (you don't have to disconnect the steering shaft like I did - I was replacing the rack):

1b5e8c1.jpg
Check out the pix at http://99intrigue.shutterfly.com/steering for help, but like I say, those are about replacing the rack. Route the hose under the right tie rod on the factory clip.

Mar 08, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Pressure line hose on the power steering pump/resorvoir is leaking and needs replacing. I need to know how to take it off the vehicle to replace the hose.


Undo the line nut on the back of the pump and undo the line nut on the steering box.. dont think the pump has to be removed to do this Line nuts are 18 mm or 16mm / 5/8s good luck

Jan 27, 2010 | 1993 Chevrolet Suburban

1 Answer

I need to change the alternator on a 2001 ford focus and need to know what size wrench is needed to loosen the timing belt tensioner enough to remove the timing belt. Please help


I don`t know the size,but it will be metric.If you have a standard,american set of wrenches,get the one that is closest to fitting the bolt head.Here is something to help you decide what the actual metric size wrench to use.8mm is 5/16,,,10 mm is smaller than 3/8.11mm is a 7/16.12mm is larger than 7/16 but smaller than 1/2.13mm is 1/2,14mm is 9/16,15 is bigger than 9/16,but smaller than 5/8.,,5/8 is 16mm.17mm is 11/16,18mm is bigger than11/16,but smaller than3/4,19mm is 3/4.I hope this helps.

Oct 30, 2009 | Ford Focus Cars & Trucks

1 Answer

Nut size on Caliper mount - '01 Jeep Grand Cherokee - 6 cylynder


What is your question? You have metric tools. Are you missing a size ? Which nut? Caliper mount or brake hose. Or torx fitting?

Sep 29, 2009 | 2001 Jeep Grand Cherokee

2 Answers

I'AM LOOKING FOR A DIAGRAM OF THE COOLING SYSTEM; SO I CAN DISCONNECT THE HEATER HOSE AND USE A WATER HOSE TO RUN THROUGH IT TO SEE IF ANY DEBRIS ARE TRAPPED BLOCKING WATER FLOW


This is how I flush the heater core...go to the garden department at Wal-Mart and get a 5/8 - 3/4" female garden hose connector similar to my picture...remove the upper heater core hose and connect your garden hose to the connector then to the heater hose and secure with a hose clamp. Remove the lower heaer core hose and point it to the gound, then turn on your faucet and run clean water thru it... b67bfc8.jpg

Mar 24, 2009 | 2001 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...