Question about GMC K1500

1 Answer

What causes a 1998 s10 2.2 to turn over alot before starting

Already replace feul pump and filter i'm getting 42lbs of pressure

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,669 Answers

Since spark, gas and air are the basis for an engine running...check for a good, clean spark going to each cylinder, Check the choke for a jammed preheater coil that is not setting the choke properly.

Posted on Jan 20, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 97 gmc 5.7L took longer to start now it wont

check the distributer cap and rotor button... may not be getting fire... easy replacement

Posted on Apr 29, 2009

michael_grey
  • 365 Answers

SOURCE: The car starts but then bogs out and dies after a few seconds

Check the fuel pressure regulator.

Posted on Aug 01, 2009

  • 4 Answers

SOURCE: toyota wont start

EFI= to Electronic Fuel Injection. If you have sparks, check for fuel delivery. Another is the electronic module on your distributor, but you already said you have spark and hopefuly the right "timming" too. So you checked the current and is OK, what else do we have.The computer? Remeber that Camry,is the cadillac of the Toyota. Some even have Lexus parts. So expect parts to be rather expensive!.

Posted on Aug 07, 2009

roniecon
  • 6927 Answers

SOURCE: i have a 2001 camaro with a 3800 v6 it cranks but

The crank sensor is what pulses the ijectors,and makes the spark,so I would start at the crank sensor.Let me know how you come out.Check for any blown fuses also.Ecm fuse would cause this,but it may be called anything ,so check all fuses.

Posted on Sep 10, 2009

SOURCE: hyundai terracan 2.9 deisal 04 runs fine when

dear friend: i think that your terracan is actually running out of fuel even if the guage shows quater,you can also put the old fuel filter back and try it,we did discover some of the new filters sucking air.

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wondering why this type of car is losing pressure


Try a new fuel filter first. From there have someone check the fuel pressure regulator and then the pump. If you are in need of a new pump, take my word for it and spend the money to get one from a Dealer, and not from your favorite parts store. Most parts store parts are made in China and they are JUNK. At least get a OE pump. If the pump has never been replaced, its probably time for a new one.

Mar 17, 2013 | 1995 Oldsmobile Aurora

1 Answer

What should compression be on 1995 grand prix 3.4 litre


Check for 42lbs fuel pressure, also check fuel pressure regular connection

Oct 07, 2017 | 1995 Pontiac Grand Prix

2 Answers

It wont start after sitting over night but will turn over really good


Verify that you have fuel pressure the next time it does this, more than likely you don't. Cycle the key from off to on about 10 times before you actually attempt to crank it over. If it fires up after doing this then you have a bad fuel pump and your loosing system pressure over time beacuse its leaking down back through the fuel pump. Replace the fuel pump, fuel filter, and the fuel pump relay.

Aug 20, 2011 | 1998 Chevrolet C1500

1 Answer

Put in a fuel pump and fuel filter and now have no pressure in the fuel rail


I dont know the year so it is difficult to be specific.Is there enough feul in the tank for the feul pump to pick up.Some feul filters have the same connections on both sides and can be installed backwards, this will cause a restriction because feul will only flow one direction.Can you open the feul cap and hear feul pump turn on for 3 seconds when the ignition switch is cycled.Let me know if i can help?

Feb 09, 2011 | Cadillac DeVille Cars & Trucks

1 Answer

1998 Dodge Caravan. engine dies and wont start. fuel pump was changed twice but i get a few miles & dies again & wont start. im thinkin fuel filter is plugged....


It might be your fuel filter. Also, Dodge and Chrysler is bad for fuel pump failures. A clogged fuel filter can cause this. Also, you might not be getting enough fuel pressure. There should be a test port on the van, where you can test the gas pressure. You also have a fuel pump relay or switch. This could be bad as well. Hope this helps you.

Jan 08, 2011 | 1998 Dodge Caravan

1 Answer

I have a 2001 chevy silverado 1500 with a 4800 vortec engine. it starts and idels fine but when ever i give it gas, the engine starts to sputter and dies. ive already changed the fuel filter and spark plug...


This sounds llike weak feul pressure, the fuelpump may need replacing, the first thing to do is have the fuel pressure tested and if the pressure is low then have the pump replaced. the pump is located inside the fuel tank and the tank will need to be dropped to replace the pump, good luck ,

Jan 01, 2011 | 2001 Chevrolet Silverado 1500

1 Answer

Will not start have new battary, new feul pump, new feul pressure, new plugs and new air filter?


Turn the ignition to on and push on the break peddle and put the car in neutral and it will start

Mar 16, 2010 | 1998 Ford Expedition

2 Answers

Vehicle won't get feul to crank. we replaced fuel


Of course you will need to check to see if the fuel pump is actually pumping, or damaged. I suggest that you remove the fuel filler cap, then have someone turn the ignition switch on while you listen through the fuel fill inlet to see if you hear the pump turn on for a few seconds then off. If you're hearing nothing and have no fuel, either the vehicle is not telling the pump to turn on, (verify voltage at the pump electric connection) or the pump is bad.

Generally, when you turn the ignition on, you should hear the pump for a second or two as it builds pressure, after replacing the fuel filter, you may need to do this several times to get pressure to the injectors, and to do that, just cycle the switch to on, then off, in 4 or 5 second intervals. The pump if working, will build pressure eventually allowing the vehicle to start. No need to crank, until you have fuel pressure, Just to "ON", then "OFF" several times.

I hope that you took the time to put some fuel injector cleaner (1/2 filled w/Gumout) into your new fuel filter when replacing it, it's a cheap fuel injector/fuel system cleaning method I've used for years when replacing fuel filters. It can cause a sputter or two initially, but does a good job.

good luck

Feb 28, 2010 | 1996 Chevrolet K1500

3 Answers

Want start unless iput feul in the carb and then it want keep running


check the fuel line , the filter maybe clog. change the filter.

Jun 11, 2009 | 1991 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...