Question about 1995 Toyota Corolla

Open Question

HOW TO REMOVE AND REINSTALL CLAW WASHER ON 1995 CORLLA INNER TIE ROD

I AM GOING TO REPLACE THE INNER TIE ROD on my 1995 corolla and would like to know how to remove and in particular reinstall the claw washer on the inner tie rod.does anyone have any suggestion on what type of tool i should use for this. I undestand there is not much room in this location.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: inner tie rod ends on a 2002 toyota celica

First, you do NOT have to remove the rack to replace the inner tie rod ends. Second, If you want a .pdf regarding the procedure, I'll be glad to send it to you. But, the tie rods just screw off. Whatyou WILL need to do is get a good front-end alignement after you replace the inner tie rod. If not, you will destroy your tires. Alignment is critical to minimize tire wear on Celicas.

Posted on Nov 13, 2008

  • 4 Answers

SOURCE: 2005 Toyota Corolla - steering column crunches

the reason why your hearing this noise is because your CV joints on your car is bad. CV joints go bad when the CV boots have a rip or a tear in them and little pebbles and debree from the road get into the bearings of your axle. Dont worry its not like this big expensive ordeal. What I do suggest is dont even ask about replacing the CV joints because it usually costs the same or even more than just replacing the axles. I know it sounds horrible expencive but its not. When you take your car in tell them you want to replace your front right and left CV axles, because there are two of them in the front. Most people think you only have 1 axle in the front but you technically have two. I find the cheapest way to do it is ordering the axles online. Then finding a job with the cheapest labor rate to put them on.

Go to www.autopartswarehouse.com. Select the year, make and model of the car. Then scroll down to the Driveshaft and Axle section and click on Axle Assembly and order the parts from there. I made it a little easier on you, I already looked it up for you and the price

right axle is $99.95
left axle is $99.95

Now you say you get the crunching when you turn left and right so you will need both the left and right axles. Remember that the longer you take to replace them, that crunching noise will continue to get louder and louder

Posted on Jan 12, 2009

GARYca
  • 672 Answers

SOURCE: 97 a toyota camry do they have replacable inner tie rod ends

they do have replaceable inner and outer tie rod ends, although I do recommend replacing the entire rack and pinion!! Hopefully this helps!!

Posted on Mar 28, 2010

  • 70 Answers

SOURCE: 1991 corolla makes a clank sound from the pass

check the bushes

Posted on Apr 02, 2010

  • 8404 Answers

SOURCE: I am replacing the inner

You will need sockets of the proper size, side cutter pliers, 16 oz or bigger ball peen hammer and a pickle fork (thing to remove the ball joint) probably regular pliers and a screw driver. You will possibly need new cotter pins and a grease gun. Other tools may be required but I would not lay down on the mechanic crawler until I had at least these items.

How do you intend to realign the front end? If you are going to do this, you will need a $25,000 wheel alignment machine. I recommend you get the alignment done at a shop equipped for this service.

Thanks for your question @ FixYa.com

Posted on Mar 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Left front wheel arm broke


go to the wreckers and get another good one and replace it

Mar 07, 2016 | 2003 Chevrolet Chevrolet Monte Carlo SS

1 Answer

Toyota camary 1995 end tie rod digram


you need to either be able to get a wrench on the Inner Nut or you need the special tool to get the Inner Off. The Correct tool makes it an EASY Job..
65f5515d-4238-4aaf-9e87-134a665da60c.jpg

Apr 16, 2013 | 1995 Toyota Camry

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

Machanic said may have loose tie rods on my 99 toyota corolla how can i tell and how do i fix, also how do i chang a o2 censer, does it uscrew and u just plug in new one and screw back in or do i need...


to check the tie rods you jack up the front of the car. Place your hands at the 9 and 3 o'clock positions on the tire. Push/pull on the tire. If you feel movement than look carefully at the out tie rod while you push or pull and see if it moves. If it does it is bad if it doesn't than the inner toe rod is bad. PYou will not be able to do the inner tie rod without some specialty tools.

The outer tie rods can be replaced by removing the tire, loosen the jam nut that holds the inner tie rod tight to the outer tie rod, removing the cotter pin (if it has one) from the tie rod end, remove the nut that secures the tie rod end to the knuckle, Hit the knuckle with a hammer where the tie rod goes through the knuckle until the tie rod comes loose from the knuckle (do not strike the tie rod end), remove the tie rod end from the knuckle and unscrew from inner tie rod counting the number of turns it takes to remove, install the new one using the same amount of turns.

After putting it back together you'll need to grease the new tie rod ends if equipped with grease zerks and have the car aligned.

The O2 sensor unthreads from the exhaust manifold as you thought. It will require an O2 socket which is a 7/8" socket with an opening down the side for the wiring harness to go through. you should be able to purchase the socket from the parts store that you purchase the O2 sensor at. DO NOT GET A UNIVERSAL FIT OR CHEAP AFTERMARKET BRAND, this will cause more problems and more money than just getting a good quality sensor from a reputable supplier or straight from the dealer.

Nov 21, 2010 | 1999 Toyota Corolla

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

2 Answers

One of the steering rods that goes from the rack to the right tie rod is bent. Can I replace the rod or must I replace the entire rack?


you can replace just the tie rod yourself although you do need a special tool but you should be able to get it at any parts store just take the outer tie rod loose from the steering knuckle remove the rubber boot from the inner tie rod and get the proper size tool to fit he nut and remove and replace the inner tie rod and install in reverse order make sure to count the amout of turns that removed the outer tie rod and reinstall the same amount of turns then afterward the car needs to be aligned

Apr 13, 2010 | 2000 Ford Focus

1 Answer

How to replace to inner tie rod


remove tire un bolt outter tie rod end from spindle where it connects loosen the jam nut remove tie rod end count how many turns it takes to get off or your alignment will be way off remove clamps off of the rubber boot one small one large there is a special tool to remove the inner tie rod but you might be able to get a pair of pliers on it turn it out when you replace the end make sure to fold the washer over the flat spots on the tie rod to ensure it wont work loose not to hard of a job

Feb 25, 2010 | 1998 Mercury Sable

2 Answers

2000 LINCOLN LS - Outer tie rod removal assistance


Yes degreaser will not hurt it. The outer tie rod is retained only by one nut that connects it to the inner tie rod.Once you have this loosen just turn the outer tie rod to the left to remove it from the inner tie rod.

Feb 24, 2010 | 2000 Lincoln LS

1 Answer

How difficult to replace inner tie rod end on 06 silverado 2wd?


Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Jun 03, 2009 | 2006 Chevrolet Silverado 1500 2WD

Not finding what you are looking for?
1995 Toyota Corolla Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...