Question about 1993 Mercury Topaz

1 Answer

Removing the left front axle on a 1993 mercury topaz gs

I cannot remove the left front axle on my 93 topaz it is recessed into the transmission and there is nowhere to put a pry bar behind it please anything would help at this point

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 373 Answers

They are held in the transmission with a snap clip. Take a small flathead screw driver and wedge it in between the axle and tranny and turn axle clock wis and counter clockwise and it will come out. When you put the new one in, you will hear it ;; snap;; in place

Posted on Jan 20, 2013

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: 1993 mercury tracer

To replace the headlight on a 1993 Tracer you must turn the black plastic retainer ring counter clockwise and then pull back gently. The ring and bulb should then slide out toward the engine.
Carefully grab the sides of the plug and pull the bulb out.
When replacing the bulb make sure not to touch the glass part or it will cause the bulb to burn out sooner. Place the black ring back over the bulb with the open end towards the glass part of the bulb. Fit the wiring onto the back of the bulb and insert the bulb back into the reflector. The black plastic ring has notches that fit over protrusions. Turn the black ring clockwise and your done. Test the headlight. Happy Driving

Posted on Jan 28, 2009

  • 2 Answers

SOURCE: oil leaking in front of my engine above the oil filter. '92 mercury topaz GS, 2.3 4 cyl

possibly the oil pressure sending unit- looks like a small spark plug screwed into the engine with one wire going to it

Posted on May 30, 2009

  • 1 Answer

SOURCE: Mercury Topaz serpentine belt diagram

I have a 93 topaz, the diagram label is under
the hood itself.

Posted on Jul 29, 2009

  • 811 Answers

SOURCE: 93 mercury topaz error codes 32 35 54 56 73

check fuel pump or relay

Posted on Sep 27, 2009

Testimonial: "Thanks for your help "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust the idle on a 93 mercury topaz?


I would clean the throttle body first and the idle air control motor(IAC). Clean where the plate sits and on the back of it/them. You have to remove the IAC to clean it. Brake clean and a toothbrush works fine. If it still is high. Diagnostics need done for the IAC. Most times it is the IAC.

Nov 01, 2016 | 1993 Mercury Topaz

1 Answer

Front axle


Remove the tire. remove the strut bolts. remove the axle nut. push the axle out of the hub(hammer out if necessary). Pull/push the hub away to get the axle completely out. Use a pry bar to get the axle out of the transmission. replace in reverse order. add fluid if necessary.

May 22, 2013 | 1993 Geo Storm

1 Answer

Amilywanting to know how to change left front axle on a 1990 mercury topaz


tire off pull brake caliper,then center axle nut, pull bolts out of strut pull spindle down so axle can be pulled out of spindle, after that done take big screw driver to trans @ axle inbetween them pop axle away from transmission remove old follow reverse to install make sure new axle seats into transmission just like old one

Aug 15, 2010 | Mercury Topaz Cars & Trucks

1 Answer

How do i replace the distributor on a 93 mercury topaz


the distributor is held by a clamp bolted to the block where the 'stem' enters the block.remove cap and mark position of rotor to ensure proper ignition timing upon re-assembly,note firing order of plugs.if a 'no spark condition exists,check 'pick-up module 'bolted to the side of distributor,below cap,a hex head 'special tool' is available to remove module w/ distributor in place. these modules are only rated for 50K miles.

Oct 06, 2009 | 1993 Mercury Topaz

1 Answer

Mercury Topaz serpentine belt diagram


I have a 93 topaz, the diagram label is under
the hood itself.

Jul 16, 2009 | 1993 Mercury Topaz

1 Answer

Oil leaking in front of my engine above the oil filter. '92 mercury topaz GS, 2.3 4 cyl


possibly the oil pressure sending unit- looks like a small spark plug screwed into the engine with one wire going to it

May 30, 2009 | 1992 Mercury Topaz

1 Answer

'93 camry left drive axle replacement problem


the c clip is down u must remove and reposition the openning down

Mar 06, 2009 | 1993 Toyota Camry V6

1 Answer

93 six cylinder mercury topaz


You have to replace the bushing on your axle, be it the right or left!

Jun 16, 2008 | 1993 Mercury Topaz

Not finding what you are looking for?
1993 Mercury Topaz Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...