Question about Dodge Cars & Trucks

Open Question

2002 dodge intrepid code p0139 p0138 and p0158

Engine light on -- diagnostic test provided by autozone and this was their reading.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

farroutideas
  • 78 Answers

SOURCE: I need a time diagram of an 2002 dodge intrepid,

Hi there;

Here is a picture of the timing marks for the 2002 2.7L intrepid engine.


Hope this helps
Farrout!

Posted on Mar 17, 2009

canbruce75
  • 1776 Answers

SOURCE: 2002 Dodge Intrepid- check engine light came on

This code indicates an automatic transmission control problem. The presence of this code means that the transmission control module or TCM has detected a fault and relayed it to the PCM. It could be a TCM related solenoid has failed or is damaged or the TCM itself could be faulty. Best wishes.

Posted on Aug 18, 2009

  • 3640 Answers

SOURCE: Failed Emision test

po442 is evap emission control system leak (small) 1 of the lines for emissions is leaking. po455 is-- emission control system leak (large). turn off light with code scanner after it is fixed.

Posted on Sep 01, 2009

ZJLimited
  • 17970 Answers

SOURCE: what is nissan quest code p0138/p0139

P0138 - Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)

P0139 - Oxygen Sensor Circuit Slow Response (Bank1, Sensor2)

The Heated Oxygen Sensor (1 or 2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

Symptoms: There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.

Causes: A code P0138 may mean that one or more of the following has happened:
* Faulty O2 sensor
* Short to battery voltage in O2 sensor signal circuit
* High fuel pressure (not as likely)

Here are some potential solutions:
* Replace O2 sensor
* Repair short to battery voltage in o2 sensor signal circuit

Hope helps (remember to rate this answer).

Posted on Oct 11, 2010

ZJLimited
  • 17970 Answers

SOURCE: 2002 nissan maxima, check engine

About DTC P1800, I suggest check the harness and verify it is plugged in and still functioning. Also, try checking your vac tubes to verify that they are not reversed. Also read this TSB with details about correct diagnostic: DTC P1800 VIAS CONTROL SOLENOID VALVE

The VIAS control solenoid valve cuts the intake manifold vacuum signal for power valve control. It responds to ON/OFF signals from the ECM. When the solenoid is off, the vacuum signal from the intake manifold is cut. When the ECM sends an ON signal the coil pulls the plunger downward and feeds the vacuum signal to the power valve actuator.

DTC detecting condition:
• An excessively low or high voltage signal is sent to ECM through the valve
Possible cause:
• Harness or connectors (The solenoid valve circuit is open or shorted.)
• VIAS control solenoid valve

Will need replaced the solenoid valve (P/N - 149558J10A). The valve is located under the engine cover. It's a Nissan only part so you have to order from the dealer, either online or in person. It's cheaper online. Check this sample Nissan engine location (click image for zoom)...

zjlimited_1658.jpg



DTC P1147 - Bank1 Sensor 2 O2 sensor maximum voltage monitoring
Component Description: The heated oxygen sensor 2, after three way catalyst, monitors the oxygen level in the exhaust gas on each bank.

Even if switching characteristics of the heated oxygen sensor 1 are shifted, the air fuel ratio is controlled to stoichiometric, by the signal from the heated oxygen sensor 2.

This sensor is made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. Under normal conditions the heated oxygen sensor 2 is not used for engine control operation.

DTC detecting condition: The maximum voltage from the sensor is not reached to the specified voltage.

Possible cause:
Harness or connectors (The sensor circuit is open or shorted)
Heated oxygen sensor 2
Fuel pressure
Injectors

Majority of cases this is either a faulty O2 sensor, or short/open in wiring harness. Bank1 sensor2 is the rear O2 sensor on the passenger (right) hand side (click image for zoom):

zjlimited_50.png

Here is simple test with voltmeter to test O2 sensor. If it fails test, replace sensor. If not, then you will have to start tracing the wiring harness for a short/open in it (click for zoom):

zjlimited_51.png

And here additional details: DTC P1147 O2 Sensor

Keep us updated.

Posted on Aug 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2002 dodge dakota 3.9 california emissions it has 4 o2 sensors. It has a p0152, p0138, and p0158. How likely is it that all four sensors are bad?


very unlikely. Though it is possible that the engine is burning more fuel than the o2 sensors can measure. This could be caused by a number of things that affect fuel management. Use these codes as a reference to identify the problem.

Nov 12, 2013 | Cars & Trucks

1 Answer

My 2002 dodge intrepid transmission shifts fine till it gets warm then it down shifts when coming to a stop and wont upshift till i turn the ignition off and restart what is the problem


Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Aug 28, 2012 | 2002 Dodge Intrepid

1 Answer

Check engine light on codes p0138 and p0139


Hi, guys. you can read this article first. Why check engine light is on. Maybe it is able to help you. Good luck.

Aug 27, 2012 | Infiniti M45 2003 2005 If 51 02 Vehicle...

1 Answer

2002 dodge durango engine light on. after diagnostic test.results indicate evaporator hoses are leaking


Check your gas cap first.

Replace the cap and have the code cleared at Autozone. If the problem comes back, look for cracks in the lines between the gas tank and the evap canister behind the battery.

Nov 11, 2010 | 2002 Dodge Durango

1 Answer

NEED TO REMOVE STARTER AND DON'T KNOW HOW


I found your solution (with pics) at:
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528006a865

However, www.autozone.com will expect you to register (free) to access their repair guide database.
Note: The Intrepid 3.5L engine takes the Delco starter, while the Intrepid 3.3L engine takes the
Nippondenso starter.
How can you tell which engine's in your Intrepid? read 8th digit of the VIN code.
VIN code "F" - 3.5L 6cyl MFI (multi-port fuel injection) - 60% of 1997 Dodge Intrepids sold
VIN code "T" - 3.3L 6cyl MFI - 40% of 1997 Dodge Intrepids sold

Oct 25, 2010 | 1997 Dodge Intrepid

1 Answer

What is nissan quest code p0138/p0139


P0138 - Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)

P0139 - Oxygen Sensor Circuit Slow Response (Bank1, Sensor2)

The Heated Oxygen Sensor (1 or 2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

Symptoms: There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.

Causes: A code P0138 may mean that one or more of the following has happened:
* Faulty O2 sensor
* Short to battery voltage in O2 sensor signal circuit
* High fuel pressure (not as likely)

Here are some potential solutions:
* Replace O2 sensor
* Repair short to battery voltage in o2 sensor signal circuit

Hope helps (remember to rate this answer).

Oct 11, 2010 | 2002 Nissan Quest

1 Answer

My check engine light just came on and its staying on what does it mean should i get it plugged ion to a diagnostic.


take it to your local autozone and they will do a diagnostic test and tell you what system is not working properly

Mar 11, 2010 | 1994 Dodge Intrepid

1 Answer

Engine light is on...


P0137--O2 Sensor Circuit Low Voltage-Bank 1 Sensor 2

P0139--O2 Sensor Circuit Slow Response-Bank 1 Sensor 2

P0152--O2 Sensor Circuit High Voltage-Bank 2 Sensor 1

P0300--Random Multiple Cylinder Misfire


I would suspect that the camshaft position sensor is bad. This is a quote from the tech manual:

The Powertrain Control Module (PCM) uses the camshaft position sensor to manage sequential fuel injection and as part of misfire diagnosis. The PCM constantly monitors the number of pulses on the signal circuit. The PCM compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the PCM receives an incorrect number of pulses, Diagnostic Trouble Codes (DTCs) should be stored in the PCM. Some PCM systems will then default to multi-port or "gang-fire" injector operation. The camshaft position sensor signal is required to sequence the injector operation to the proper cylinder timing. If the camshaft position sensor or circuit is faulty, most engines will start. However, the PCM misfire diagnostic will likely be affected.

aa26193.jpg
5ac44c6.gif
The part costs $50.....simple to change. It is NOT the O2 sensors so don't go wasting money on those. They are being affected due to related symptoms....they fault because the problem is happening upstream.

Oct 01, 2009 | 2002 Dodge Intrepid

1 Answer

Check engine light


I would say that your o2 sensors are faulty either the pre or the post . They must be intermitten so I would replace both

Mar 24, 2009 | 2004 Dodge Stratus

1 Answer

My 2002 Dodge intrepid has it engine light on


The MAP sensor and Knock Sensor are both very easily replaced. A better scanner will tell you which sensor is going bad on your transmission. An Autozone code reader will not tell you which sensor on the trans. is acting up. Most sensors on your trans. are very easity replaced as well. They just screw in and plug it. It's worth paying to get a "real" scan done. The trans. sensors are inexpensive and you can replace any other your listed sensors yourself.

Jun 30, 2008 | 2002 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...