Question about 2008 Toyota RAV4
First turn of the key, long crank time then starts. second turn of the key , quick start.
Check the fuel pressure regulator to see if it holds pressure when the engine is not running.
Posted on Nov 21, 2014
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
your starter is bad.... the two contacts inside the solinoid are worn out only way to fix is replace the unit as a whole bet ya you get click click click then my start.. bet my life on this one been fixin toyotas for 20+ years
Posted on Dec 30, 2008
SOURCE: Keyless Remote 2008 RAV4
You can take it back to the dealer, and have them change the battery, or go to Autozone, buy the battery and do it yourself. They can show you how to do it. And which battery it takes. It's not hard to do. Good luck.
Posted on Jan 27, 2009
I have just replaced my water pump on my 1998 RAVE4, also, the timing belt and the other two belts. I had a tough time with the timing marks. The way you line these marks up is easy if you take the time, First, if you are changing the timing belt you pull the balancer and both top and bottom plastic covers,(do not try to pull top cover off before you take off balencer and the motor mount off or you will just break it.), Second after covers are removed you will have access to the timing belt, you can now remove it by loosening the tensioner bolt and pushing down on the tensioner wheel, the belt then can be taken off. Third take out number one sparkplug and replace the bottom cover by maybe two bolts so that you can see marks on cover, next replace the balancer and bolt. Turn the motor over by hand with the balancer so the small divit on the back of the balancer is on 0 or top dead center on the compression stroke, you can use a compression gauge for this or I just used a mirror and light to shine in the number one cylinder to see the piston. Next remove the balancer and cover and make sure to make a mark on crankshaft gear and housing. Next you will need mirror and flashlight, now turn camshaft gear clockwise to line the hole in the gear with the top timing mark. I recommend a small circle mirror for this. Now replace the belt. I turned the crank shaft gear one tooth counter clockwise off mark and the camshaft one tooth clock wise off mark so when the belt is on you can turn the camshaft gear counter clockwise to get tension on the belt and marks will line up. I would recommend changing water pump,tensioner wheel, and the idler wheel. After belt is on I would replace the bottom cover the balancer and the crankshaft sensor. Iwould then start it to make sure the water pump is not leaking and the motor is not pinging or you will have to tear it back apart again. Good luck and no I am not a certified mechanic just thought this would be helpful from my own experience.
Posted on Apr 30, 2009
Hello I have simular problem the ignition on is stuck in that position with the key turned off and out of the ignition switch.It feels like the key switch is spinning freely in the ignition. Do I need an ignition switch?
Posted on Aug 05, 2010
Tips for a great answer:
Apr 13, 2016 | 2004 Toyota RAV4
Apr 13, 2016 | 2004 Toyota RAV4
Apr 15, 2014 | 2008 Toyota RAV4
May 06, 2010 | 2008 Toyota RAV4
Feb 25, 2010 | 2008 Toyota RAV4
Nov 15, 2009 | 2008 Toyota RAV4
Aug 08, 2009 | 2008 Toyota RAV4
Jul 01, 2009 | 2008 Toyota RAV4
223 people viewed this question
Usually answered in minutes!