Question about 2008 Ford Edge SEL

Open Question

My automatic door locks don't lock on my 2008 Ford Edge

Speed sensitive door locks don't engage

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Door lock problem

I have an expedition with the same problem.To fix it just spray some PB blaster on locking mechanisms.WD 40 works also but may melt the wiring harness.I used wd 40 and I have had no problems since. GOOD LUCK.

Posted on Jun 27, 2008

Ad
  • 65 Answers

SOURCE: Auto door locking on Ford Mondeo

It sounds like it has been deactivated so we are going to reactivate the auto lock.

The numbers I will be saying will have to do with getting this to work so:
you will need to put the key in to the ignition switch.

1= is back to listen to the radio
2= is to get key out
3= is just before you start
4= is for starting your car

When we do this 1 and 4 will not be used
Do this and we will hope that it works like it should:

1: Turn the ignition with you key up to on( don't start)

2: Press the power door lock control 3 times

3: now turn the key back once (to off position)

4: Press the power door unlock control 3 times

5: ok turn the ignition back up 1 time. (The horn should chirp)

6: Then press the unlock control, then press the lock control, again (horn will chirp 1's) If auto lock
was activated.

7: Turn the ignition back 1's, Then the horn should chirp once to confirm the procedure was completed.
Nikki2913

Posted on Nov 29, 2008

  • 4369 Answers

SOURCE: 2000 Ford Focus automatic door locks quit working.

check fuse 63 first.

Visual Inspection Chart Mechanical Electrical

  • Binding latch mechanisms
  • Binding linkage
  • Misaligned door
  • Central junction box fuse 63 (20A)
  • Damaged wiring harness
  • Loose or corroded connection(s)
  • Circuit
  • Door lock switch
  • Door lock actuator



It could also be your GEM (generic electronic module) which is expensive as it controls a lot of stuff. A scan tool can be used to cehck for fault codes from the GEM.

Posted on Jun 23, 2009

laseramp
  • 314 Answers

SOURCE: i have a 2006 ford focus and my back door

sounds like the fuse that controls that switch has burned out. check your fuse panel and refer to either the manual. or to the cove for fuse location info. good luck.

also note if the fuse blows again then the problem might be related to a bad switch or a short condition ion the wire.

Posted on Oct 01, 2009

  • 1 Answer

SOURCE: I cant find the door code for my 2007 ford edge

it under the sterring wheel by the fuse box is where i found mine its a 5 didget code

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Dodge ram van 3500 door will not open. power locks that cick on for open & close don't work


Not easy to find, incorporated in the lock itself, usually a little tag sticking out to pull/push, but it is normally on the side you can't get too, I take the lock out complete and then you know what you are working with, you can see how it all works that way!!

Mar 06, 2018 | Cars & Trucks

1 Answer

The electric doorlocks don't function


anytime anything electrical suddenly stops working, check the fuse. if blown, replace, if blows again, find the short.

Feb 01, 2013 | 1995 Ford Taurus

1 Answer

I have 98 Camry Le and the door locks lock automatically shortly after the doors are unlocked and the alarm will set also. What could be the problem? Alarm Control Box?


if you use the keyless entry to unlock the vehicle & don't open a door within 30 secs.the vehicle will automatically lock & the alarm will reset,if you unlock it with the key this shouldn't happen.....cheers.

Sep 01, 2011 | 1998 Toyota Camry

1 Answer

The passenger door has lost all pwr. The window, mirror & lock won't work. The dealer says we need a door control module to the tune of $452.00 . I want to find one online & replace it myself...


Hi

The door control module actually consists of the door's Electronic Control Unit (ECU) and the switches or buttons integrated into one assembly. There are two of them: the driver door module or DDM (as seen on the sample diagram below) and the passenger door module or PDM, which is on the right front door. These modules are programmable.
They are also called driver door switch (DDS) and passenger door switch (PDS), so perhaps you can rephrase your search.

Please check this links to get some useful information:-

http://www.2carpros.com/articles/test-or-change-electric-power-door-locks

also check the picture attached:-

godblessu.gif

Please get back to us if you have further query or else please accept the solution.

Aug 30, 2011 | 2003 Oldsmobile Bravada

1 Answer

Doors wont lock. Windows won't work. Car thinks the door is locked because when I open the hood alarm goes off. Security light is flashing when doors are closed. Locks don't engage when driving...


Window fuse's and relay's may be up under driver or passenger side dash or behind glove box, under the hood and even under the seats, and finally on the ends of the dash. All passenger power windows and locks are controlled thru and get power from the master control switch on the drivers door. Could be a broken wire in the rubber boot going from the door to the body. You will have to eliminate each till you find the culprit. Check that all switches return to neutral when released. It could also be the body control module.

Aug 28, 2011 | 2003 Volkswagen Jetta TDI

1 Answer

My 2000 licolin battery died the key won't open the door lock how do get in to the engin to put jumpers on the battery to give it enough power to work the locks ps i don't understand why the key...


The key has to open the drivers door

Raise the car up,support it,& put your battery
charger on the starter battery cable terminal
& ground the black clip

Try charging the battery for 4 hours or so

Jul 02, 2011 | 1998 Lincoln Continental

1 Answer

Have all gears that work find but will not go in reverse it a 5 speed


Is this a new truck to you? Some manual's have a manual reverse lock-out, meaning you have to engage the lock-out to shift into reverse. This is usually done by pulling up on a small lever just under the shift knob.

Otherwise, the lock-out is inside the transmission and if that breaks, the transmission has to be removed to fix it.

The other possibility is that you don't have a synchronized reverse gear. It will not automatically sync with the engine speed. Try lightly putting it in reverse while letting the clutch up to the engage point, you know, right where the clutch first starts to grab.

Jun 07, 2011 | 1992 Nissan Pickup

2 Answers

How do I put my 09 Suzuki SX4 AWD in lock position ?


You have a switch down by the shifter, on the side. You simply toggle the switch to lock position. You don't what to do that on dry pavement. Just put the switch in auto. The computer will engage and disenage when needed. Don Suzuki guy

Oct 04, 2009 | 2008 Suzuki SX4

Not finding what you are looking for?
2008 Ford Edge SEL Logo

Related Topics:

1,064 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...