Question about 1986 Toyota 4Runner

1 Answer

Wont crank at all

Replaced fuel pump,coil and igniter,plugs and wires,computer,mass air flow and it did not do nothing

Posted by on

  • 4 more comments 
  • jchan1120 Jan 26, 2009

    where are the located?

  • jchan1120 Jan 26, 2009

    its getting fire and gas? so the cam or crank censor could be the solution

  • jchan1120 Jan 26, 2009

    i was 4wheeling and it started missing and would not stay running so we pulled it. for a coupled days when u would try to crank it would fire for a second and die,then it would not do nothing. now it wont do nothing

  • jchan1120 Jan 26, 2009

    it wont do nothing, but u can pull the plugs and they fire and get gas but wont hit a lick

  • jchan1120 Jan 26, 2009

    the parts house said there was not acam or crank sensor for the 2.4 22re

  • Travis Humphries
    Travis Humphries May 11, 2010

    Have you had the Starter and Solinoid Checked out???? It sounds like a Classic Bad Starter

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

What about the cam and crankshaft sensors?

Posted on Jan 26, 2009

  • 1 more comment 
  • Ronnie Houston Jan 26, 2009

    the crankshaft sensor is on the bottom of the motor the cam sensor is located on the cam cover they are both plugs i believe

  • Ronnie Houston Jan 26, 2009

    most likely the cam sensor is bad if youre getting fire it means the crankshaft sensor is good

  • Ronnie Houston Jan 26, 2009

    will it even try to turn over? if so and ur not getting any fire now replace both the cranshaft sensor and the cam sensor

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My dodge neon shut off and wont start


What year? First check for spark at any of the sparkplugs.If you have spark and fuel pressure then take the mass air flow sensor off and clean the small thin wires inside with a non-chlronated brake cleaner and let it dry for 10-15 minutes then re-install it and see if it will start.

Oct 15, 2012 | Dodge Neon Cars & Trucks

2 Answers

1998 GMC Sierra 2500 5.7L hard cold starts last month, now won't start cold w/o a little carb cleaner in intake. Codes for oxy sensors, mass air sensor and crank/cam position. Drove today, no power just...


starting definately has a lot to do with the crank/cam position sensors, but it wouldnt have nothing to do with hot or cold weather, oxygen sensor will make the vehicle run too rich if its out, you will smell fuel very strong out the exhaust, that could make it run sluggish also, and usually if the mass air flow sensor goes out the vehicle wont start at all...

Nov 27, 2010 | 1998 GMC Sierra

1 Answer

Car war hesitating and missfiring so i replaced the fuel pump because the code reader said lean fuel and i researched to see what could it be and it revealed it could bethe fuel pump or the mass air flow...


normally a fuse burns out because of a short in the wireing and/or the item the fuseis running is defective...(check o2 censors, spark plugs"plugs,wires", and the ignition coil...

Jul 20, 2010 | 2006 Chevrolet Cobalt

1 Answer

My subaru was running fine and later on the highway the car shut down;i cranked it again and it shut down after about 2miles. I changed out the fuel filter and the fuel pumps,but nothing worked. I have...


Try changing the ignition coil.
The easy way to test this, is turn the ignition on,for about thirty second's ,then feel the coil ,if it is hot ,replace it.

Mar 08, 2010 | 1996 Subaru Legacy

1 Answer

Turns over but wont start


OK three essentials for a running motor......

1. Fuel - Check to ensure you have gas up to the engine. Check fuel filter, fuel pump and fuel injectors.
2. Spark - Make sure your system has electrical current to fire the plugs. Check your wires to the coil(s) the plug wires, cap & rotor and spark plugs and gaps.
3. Air - Check to make sure any air flow sensors are connected, most cars wont run with the MAF (Mass air flow) sensor disabled. Check your air filter to make sure its not dirty. if it is it can restrict air flow and cause your motor to flood its self out instead of allowing the gas to ignite, hope you found my answer helpful!

Dec 19, 2009 | 1992 Volkswagen Passat

2 Answers

97 jetta wont start


Change the crankshaft sencer.

May 29, 2009 | 1997 Volkswagen Jetta

2 Answers

1995 Eagle Talon Will not start


check the mass air flow sensor, if this is bad then the ecu wont get a signal and it wont send the right amount of fuel to the cylinders causing a no start condition

Jun 25, 2008 | 1995 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...