Question about Cars & Trucks

1 Answer

How do I no When my wheel bearing in my truck are not good does it start to here noes or u can see oil thank s for ur help

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    Uploaded 5 video answers.

  • Expert
  • 88 Answers

They could start making noises like squeeling or a growling sound. There will also be some play. If you suspect their bad my best advise is to have them checked. You dont want them to fail.

Posted on Jan 19, 2013


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 972 Answers

SOURCE: how to replace rear wheel bearing on 2003 chevy

its not hard but you do have to remove diff cover and then take out spider shaft to remove clips that hold axle. then remove bearing with slide hammer or puller. if bearings are bad so is the axle because its part of the bearing

Posted on Jun 20, 2010

  • 77 Answers

SOURCE: The truck makes a noise when starting out turning

may be the cv shaft between the diff and the bearing the joint freezes up on 1 cup and it will bind

Posted on Jul 25, 2010

  • 613 Answers

SOURCE: Hello, I removed the 3 bolts from the back of the

use a gear puller

Posted on Sep 11, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have a 2001 7.3 power stroke that started making a different sound not real agressive but I can tell a diffence and the oil pressure guage recently stoped working at idle

Check first ur oil level and oil filter and oil flow if good next ur oil pressure switch next ur oil pump need to tap pressure gage where oil pressure switch is to see if pump is working properly at idle and need to check cylinder pressure to be close to equal also crank and cam bearing is a possibility for sound detection. Good Luck

Dec 21, 2016 | Cars & Trucks

1 Answer

My AVEO 2006 is making a humming noise, coming out in the middle engine compartment of the front or dashboard area. It start to be hear when speed goes between 55 kph and 80kph, and sounds like it is

The most common reason for a humming noise in the front area of your car would be a wheel bearing noise. I would start by having the wheel bearings checked.

There are two ways to check the bearings, one would be to jack wheels of the ground and check for free play in wheels, the other would require having a tech test drive the car, a good test drive by a tech can tell you if it is a wheel bearing problem.

A wheel bearing noise will get louder as the speed increases and the tone will change if the wheel is turned left or right.
You can try this test yourself, get car up to speed of noise and then listen as you turn wheel to left and then right and if the tone changes then i would suspect the bearing and next step is to find out which one, this would need to be done on a lift. good day

Jul 01, 2012 | Chevrolet Aveo Cars & Trucks

1 Answer

How to remove rear wheel bearings on my 1999 Ford Expedition and how do i know what pulley to rent/buy?

The 1999 Ford Expedition is built on an F150 platform. The Expedition uses a 9.75-inch rear axle. The axles are retained with C-clips at the end of the axle shaft, inside the differential carrier. The axle bearings are of the roller type. A failed axle bearing can manifest itself as a noise at the rear wheel or gear oil leaking past the oil seal. When replacing axle bearings, the oil seals must also be replaced.
Torque the caliper mounting bolts to 30 foot-pounds. Torque the bolt to 20 foot-pounds with a torque wrench and socket. Click this link below for complete detailed procedure:--- -------------- This should help.Thanks.Helpmech.

Jun 07, 2011 | Ford Expedition Cars & Trucks

1 Answer

My 1999 cad sounds like airplane when 25-60mph... i thought it might be the bearings, but i check it already

an easy way to chek for faulty front wheelbearings is to drive the car about fifty mph then slowly turn the steering wheel to the left then back to the right, if ur noise changes as u move the wheel bak an forth its ur wheel bearings. othrwise gonna need more info on wat its doin to help with ur complaint good luck

May 01, 2011 | Cadillac DeVille Cars & Trucks

2 Answers

Need to know how to install wheel bearings on a chevy cavalier

1) Break the torque on the center wheel nut and remove the nut and washer before jacking up the front end. 2) Jack up the front and remove the tire. 3) Remove the brake caliper and rotor. 4) After removing the rotor you will see the bearing assy. There are 3 torx bolts holding it on. You need to put the transmission in neutral to turn the hub and line up the hole to remove the bolts. 4) Knock it loose with a hammer and install in reverse order. The kit comes with a seal but I don't believe it's needed on a 96. Pretty simple job really... Good Luck.

Feb 19, 2010 | 1996 Chevrolet Cavalier

1 Answer

Motor bearings or wheel bearings??

well if its engine bearings your talking about taking apart the bottom half of engine oil pan oil pump and many more parts just to get to these parts hoping you have enough clearance to get to any of these parts on bmw ur talking about a good $2000-3500 job depending on mechanics parts sometimes are affordable but labor is not so cheap..wheel bearings are different story depending on mechanic parts 150 labor 150-250

Jan 29, 2010 | BMW 318 Cars & Trucks

3 Answers

Sounds the transfer case is making a howling noise when driving down the road

Gears are low on oil or the chain drive is worn out or input output shaft is worn out. Check oil level first.

Nov 13, 2009 | Dodge Ram 1500 Cars & Trucks

1 Answer

I changed out the waterpump and two weeks later its KNOCKING so i chyeck everything i did then pulled off the pan and sure enough the # 5 cyl.rod had spun a bearing. i replaced All the Bearings and 15 min...

mate u have to get ur crank shaft polished.very soon it will knock as soon as u start.dont start too much otherwise u have to change ur crankshaft.service every 5oookms and good expensive oil please

Oct 04, 2009 | 2001 Dodge Intrepid

1 Answer

Grease and differential oil inside left rear drum

Not that difficult, raise and support the rear of the truck and remove the wheels. Might as well replace both sides so you know you have new seals, remove the differential cover and drain the fluid. Once differential is opened and cleaned , remove the axle "C" clip that hold the axle in place and slide the axle out. Once the axle is out remove the wheel seal and clean around the area. This would be a good time to replace the wheel bearing too since you have access to them and there not that expensive. Install the new bearing and seal, note make sure you oiled the bearing and seal before installing it back and take care when installing the axle back in and "C: clip. Use RTV silicon gasket maker to seal the differential cover and wheels back on and lower. If your lazy like i am, you can drain the differential fluid and replace it with a 50/50 mix with gear oil and Lucas engine oil additives. That may stop the leak and get you a few more miles. You gear oil is (ford 75W-140) (Dana 80W-90)and the capacity is 2.6 liters and 3.5 liters if you have the 10.25 Ring gear. Good luck and hope this helps.

Jul 07, 2009 | 1998 Ford F150 Regular Cab

2 Answers

Engine vibration in drive or reverse

Wow..thats not good..first have motor mounts checked, maybe the tranny mount or possibly if ur car has it is the driveshaft bearings...good luck on the oil leak...maybe tranny fluid..make sure if ur losing fluid that ur checking them incl. the tranny fluid...u might find ur leak first of all by rechecking the oil cap where it is supposed to be ...same with all fluid caps.

Feb 27, 2009 | 1997 Acura TL Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides