Question about 2000 Nissan Maxima

Open Question

P1320 maxima code - 2000 Nissan Maxima

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

hiseyj
  • 99 Answers

SOURCE: i have a 1999 nissan maxima with code P1320

This code is a crapshoot. There are two main things it could be and they are both expensive. There could be wire breakage in the engine harness. There is a thick harness coming out of engine bulkhead on the passenger/right side and it has a slight bend to it. With the engine idling grab that bend and give it a couple of twists and yanks. If the engine stumbles or misses that is the source of your troubles. If not, you more than likely need to replace the coils. Any one of the six coils could be causing the code so I recommend replacing all six at the same time. You could buy one coil for the front bank and one for the rear and swap it between cylinders to see which coil is causing the code. This is time consuming but cheaper.

Posted on Nov 26, 2008

  • 416 Answers

SOURCE: 2001 nissan maxima gle crank no start code p1320...please help

Primary ignition fault. Reasons: Bad distributor cap (most likely) or ignition control module/ignition coil.
Hope that helps
Good Luck

Posted on Mar 18, 2009

dsacco86
  • 1077 Answers

SOURCE: 1999 Nisian Maxima and need to know what codes mean?

P1320 Ignition Signal
Signal wire from distributor
P0325 Knock Sensor 1 Circuit Malfunction (Bank 1 or Single Sensor)
O2 senor ( The one before the cat converter )
P0300 Random/Multiple Cylinder Misfire Detected
The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we have either multiple cylinders misfiring, or the computer simply can't determine the specific cylinder, and as such we are left with the P0300 in computer memory.
Possible Causes:
Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect fuel pressure

EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Posted on Apr 13, 2009

NismoMaster
  • 146 Answers

SOURCE: engine diagnostic code P1320, 2000 nissan maxima

P1320 is the Ignition Signal Primary. There is a technical bulletin for this code for this vehicle. To remedy this issue, you will need to replace all 6 ignition coils. I suggest that you purchase them from a Nissan dealer to make sure you get the right ones.

Posted on Dec 11, 2009

alicantecoli
  • 22095 Answers

SOURCE: Code P1320 on maxima

P1320 Ignition Control Signal Fault try changing crank sensor

Posted on Oct 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1320 2000 broken wire


Here is a link to a Nissan forum that discusses your problem..In the 2nd post there is a link to the service manual for trouble shooting this issue. It seems that it is more common than not.

http://x.nissanhelp.com/forums/maxima/9813-2000-nissan-maxima-p1320-code.html

Oct 26, 2011 | 2000 Nissan Maxima

1 Answer

Code P1320 on maxima


P1320 Ignition Control Signal Fault try changing crank sensor

Oct 14, 2010 | 2001 Nissan Maxima

1 Answer

What is P1320 manufacturer code


I found a thread on Maxima.org relating to the P1320 error code. Specifically, 2000-2001 Maxima's have had this problem. It seams as though everybody agrees that the error is caused by the ignition coils. We've never had ours changed, so I'm doing that. Nissan was going to charge me approx $600 (plus tax) for parts and another $180 for labor. The job take a whole 30 minutes to replace the 6 of them, and you can get the 6 ignition coils at O'reilly's for $325. I changed three last night and the car seems to be doing better. I'll replace the other 3 tonight and see what happens.

Also, when testing the car, the car seems to "shake". I'm not sure if this is related to the P1320, but if we turn off the AC the "shaking" stops.

Hope helps (remember rated this).

Jun 01, 2010 | 2000 Nissan Maxima

1 Answer

Engine diagnostic code P1320, 2000 nissan maxima can you please let me know what sort of problem or repair this code represents.


P1320 is the Ignition Signal Primary. There is a technical bulletin for this code for this vehicle. To remedy this issue, you will need to replace all 6 ignition coils. I suggest that you purchase them from a Nissan dealer to make sure you get the right ones.

Dec 07, 2009 | 2000 Nissan Maxima

3 Answers

2001 nissan maxima gle crank no start code p1320...please help


Primary ignition fault. Reasons: Bad distributor cap (most likely) or ignition control module/ignition coil.
Hope that helps
Good Luck

Mar 18, 2009 | 2001 Nissan Maxima

1 Answer

I need to troubleshoot dtc p0325 & p1320 on a 1997 Nissan Maxima GXE?


Hi,

The two codes seem to be related. The P0325 description is knock sensor circuit malfunction and the P1320 is ignition signal - circuit malfunction.

I'll summarize and then give links on more detailed articles I found. Basically the P0325 refers to the knock sensor and associated wiring. The P1320 refers to the ignition coil and wiring. Check the sensor, coil, and associated wiring.

I found some great articles:
P0325 - http://www.obd-codes.com/p0325
P1320 - http://autorepair.about.com/library/a/1i/bl039i.htm

Good luck!

Oct 19, 2008 | 1997 Nissan Maxima

Not finding what you are looking for?
2000 Nissan Maxima Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...