Question about Chrysler Fifth Avenue

Open Question

Replace fuel filter in a chrysler fifth avenue 1990

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MNfisherman
  • 11896 Answers

SOURCE: I have a 1990 chrysler fifth avenue and it does

Most likely tranny actuator or the tranny itself.

Posted on Oct 28, 2009

Ad
shocktroop40
  • 155 Answers

SOURCE: Replace a fuel pump on a 1993 Chrysler Fifth Avenue

It sounds like a fuel line broke, most likely because it rusted through. The fuel pump is running otherwise you wouldnt see any fuel spewing out from under the car. Get under the car and see where the line broke. In most cases, you can replace the broken section of line and it will be fine.
To answer your question though, to replace the fuel pump, you will need to remove the fuel tank from the car, as the pump is attached to the sending unit inside the tank. To remove the tank, you will need to disconnect the fuel filler neck, the fuel lines, and unplug the electrical connector, then get a jack under the tank and remove the straps holding the tank in the car. Lower the jack and you will be able to access the top of the tank where the sending unit is located. Romove the lock ring holding it in, and remove it from the tank.

Posted on Nov 21, 2009

Testimonial: "Got exactly the information I suspected was my problem."

  • 3 Answers

SOURCE: I need a belt diagram for 1991 chrysler fifth avenue

belt diagram shuld be on the inside of the hood unless its been wrecked or replaced?

Posted on Jan 13, 2010

precisionaut
  • 10 Answers

SOURCE: powersteering pulley bolt on or press on for the

My info say's press on.Just in case your not aware you need the proper tool to remove and install or else damage is likely..Good luck

Posted on Jan 13, 2010

wracefans24
  • 1985 Answers

SOURCE: chrysler new yorker fifth avenue 1990 wit the 3.3

pressed on you need a puller to remove it and to push it back on

Posted on Jan 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are there any videos of changing the fuel pump for the 1990 chrysler fifth avenue that i can watch


you have to drop the fuel tank this video link has some of the older chryslers and a chrysler repair manual on video
90 fifth ave fuel pump Yahoo Video Search Results

Sep 13, 2016 | Chrysler Cars & Trucks

1 Answer

What is the procedure for removing the power steering pump


1982 Chrysler New Yorker Power Steering Belt Removal ...

? 0:35
www.youtube.com/watch?v=vZD17F_ao-o
Jan 18, 2015 - Uploaded by Kerman 559 Sanchez
1982 Chrysler New Yorker Power Steering Belt Removal ...1990 Chrysler New Yorker Fifth Avenue Start Up, Engine, and In Depth Tour ...

1990 chrysler new yorker 3.3 power steering pump change ...

www.fixya.com/cars/t15056742-1990_chrysler_new_yorker_3_3_power
Nov 18, 2012 - SOURCE: 1990 new yorker alternator replacement. You are right aboutremoving the motor mount. You have to support the engine with a jack.
images for 1990 Chrysler New Yorker remove power

Oct 20, 2015 | 1990 Chrysler New Yorker

1 Answer

Abs motor on 1990 chrysler fith ave,need wireing diagram


Its a 1990 fifth avenue,why would you even think of putting time and money into fixing ABS....It was optional equipment in 1990,and is just like driving any car without ABS...

Jul 15, 2010 | 1989 Chrysler Fifth Avenue

1 Answer

Chrysler new yorker fifth avenue 1990 wit the 3.3


pressed on you need a puller to remove it and to push it back on

Jan 13, 2010 | 1990 Chrysler New Yorker

1 Answer

My 85 Chrysler runs ok for 20 mins than it just quits,replaced fuel pump, coil, inline fuel filter,complete distribeter.


It is more than likely temp. related. Check the coolant temperature sensor, and possibly all your vacuum hoses. This car still has a pcv valve too. Change that .
See if you have any critter nests in the air intake. The duct that actually feeds through the air filter

Nov 17, 2009 | 1985 Chrysler Fifth Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...