Question about Cars & Trucks

1 Answer

Car won't start. Will turn over but not start.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Year, make and model ?
Was there a problem with those parts before you replaced them ?
Have you checked fuel pressure ?
Are you getting spark to the plugs ?

Posted on Jan 19, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 33 Answers

SOURCE: 1995 Buick Park AV intake manifold gasket starting to leak

THIS IS VERY COMMEN IN FACT JUST ABOUT EVERY SINGLE 3.1AND 3.4 AND 3.8 EVER MADE BY CHEVY LEAKS AT THE LOWER INTAKE ALL OF THEM AND USEALLY STARTS AT ABOUT 50000 MILES THE PARTS COST ABOUT 300.00 AT THE DEALER FOR NEW GASKETS AND COOLENT AND SEALENT ALL THE PARTS YOU WILL NEED THE PROBLEM IS ITS ABOUT A SIX HOUR JOB SO THE LABOR KILLS YA BUT IT IS ALOT OF WORK BUT THE GOOD PART IS THERE IS NO NEED TO REMOVE THE PUSH RODS ON A 3.8 LIKE YOU DO ON A 3.4 I CAN GIVE YOU THE STEPS IF YOU LIKE BUT THIS JOB IS BEST TO SEND TO A MECHANIC AS IT HAS A LOT OF LITTLE THINGS THAT MUST BE DONE OR YOU CAN MAKE A BIGGER MESS THEN YOU GOT ALREADY... HOPE THIS WAS HELP FULL LET ME NO IF YOU NEED MORE INFO

Posted on Mar 27, 2009

  • 43 Answers

SOURCE: service engine soon light on 2002 chevrolet tahoe stays on

That normally means that you have a issue with your gas cap try replacing your gas cap first then diconnect the negative terminal of the battery for about three minutes to clear the memory and start the truck again

Posted on Apr 11, 2009

ourhowse
  • 2007 Answers

SOURCE: 1991 Oldsmobile Cutlass Ciera idles high

Change your idle control sensor, but first make sure your throttle linkage isn't sticking.

Posted on Jun 03, 2009

  • 98 Answers

SOURCE: i have replaced the head gasket and intake

need to track down which cylinder it is. undo each plug wire separtely. when there is no change in the motor that is the one, you may get by with just a wire change.

Posted on Jun 11, 2009

  • 52 Answers

SOURCE: replaced intake manifold gasket now the car wont

If engine hydrolocked from coolant entering the engine from the gasket failure it may have damaged the engine to where it will not start until further repairs.

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

C200 Car shut off whilst I was driving. It has some power but won't crank over. Replaced the crankshaft position sensor and the car still won't crank over. Auto electrician said he was unable to scan


try to bypass the starter motor see the diagram attached.
If there are not function, test the ignition coil+PCM+BCM, etc any part can be faulty. 0161719d-dff5-4726-a652-08d0f17e7066.jpg see the diagram, get another information from another scanner repair shop.
God bless you15f71ec8-d658-438e-9813-a33ae1bc0136.jpg245792b1-b6d6-44f4-972a-8c2aedbe0f3e.gif

Jul 10, 2013 | 1998 Mercedes-Benz C-Class

1 Answer

Dodge Avenger 96 2.0L Won't Start


my wife had a 96 chrysler cirrus with the 2.6 v6 engine. the distributer was under the intake manifold and had the cam position senser in it. this is the hottest area in the engine, very bad engineering, replaced the distributer four times, each one averaging four months, spent $2500, finally sold car and would never buy another chrysler product.

Mar 12, 2013 | 1996 Dodge Avenger

2 Answers

98 blazer 4.3 engine won't start code p0336, already replaced crank sensor


which crank sensor do you replaced ? the P0336 means P0336 Crankshaft Position Sensor A Circuit Range/Performance.

________________
autel maxidas 708

Feb 25, 2013 | 1998 Chevrolet Blazer

2 Answers

My 2000 honda civic wont turn over and has no spark but the ignition coil and modual are both fine


Won't turn over? Do you mean the starter won't crank the engine over?

Or the engine cranks over and won't start, and you have tested for spark when cranking and have no spark? And then you have tested the coil and ignition module, and they tested out good? Am I on the right page here? If so, maybe the next thing to check would be the crank position sensor. The ecu (computer) signals the ignitor (ignition module) when to initiate spark after it digests the signals from the crank position sensor and the cam position sensor.

Nov 04, 2012 | 2000 Honda Civic

1 Answer

Just changed Intake Manifold, now Crown Vic won't start


first check if there is fuel coming through then check your nock sensor which is on the crank pully then *** back 2 me

Oct 23, 2012 | 1997 Ford Crown Victoria

1 Answer

2002 Daewoo Lanos 1.6 L engine- Car cranks over, but will not start. Sprayed gas in air intake manifold and car will start and idle perfectly. The whole ignition system has been replaced. Fuel system...


Either the injectors are incapable of spraying fuel or they aren't receiving an electrical pulse. That might be because of faulty wiring/connections or a faulty ECU or it could be the ECU hasn't enough information in order to send a pulse, again because of faulty wiring or connections, the crank sensor or perhaps that is what the security immobiliser does when it is armed.

Check for an injector pulse with an oscilloscope or noid light.

Jul 29, 2017 | 2002 Daewoo Lanos

2 Answers

My 1999 Buick Park Ave started hesitating and the CEL would flash. I would back off the accelerator and it would smooth out and the light would go off. About a month ago the car died while I was driving it...


Have you tried the reset method? Turn key to the ON position and leave it there for 10 minutes, or until the security light goes off. Then turn key to off, and back to on and start-see if it starts after letting it sit for a few minutes like that with the key in the on position.

Apr 11, 2017 | 1999 Buick Park Avenue

2 Answers

Front right side hit . replaced concerter and won't crank over /or start fuel pump doesn'd even come on when key is on ?


ricks63toy, I believe that Ford still uses what is called an inertia switch even in the hybrids. This switch will shut off in the event of an accident shutting off the fuel pump. This is a safety feature built into the vehicle. Seeing that this is a newer vehicle I trust that you still have the manual. If not, the switches are usually located in the trunk. Look on the side walls of the trunk and see if you can locate it. It is usually marked by a sticker. When you find the switch, push the red button down until you hear a click. This will reset the switch and allow power back to your fuel pump. Good luck with this.

May 17, 2011 | 2010 Ford Fusion Hybrid

1 Answer

Turns off on its own


Crank position sensor and camshaft position sensor.

Feb 23, 2010 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...