Question about Cars & Trucks

Open Question

What size socket do I need to change a starter on a Kia Sorento 2004

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: crankshaft sensor for 2004 kia sorento

The above information about the sensor being located at the top of the motor to the passenger side of center is bogus. That is only the pig tail plug in. The actual sensor pig tail continues down below, underneath the plastic lower timing belt cover, on the front of the motor, just above the crankshaft timing gear.

It is a very involved process of removing and replacing. You will have to remove all of the belts, the front timing belt covers, (upper and lower). You will also have to remove the front bracket that is mounted to the front of the block, which serves as the mount for the power steering pump, the alternator and the A/C compressor.You will also have to remove the crankshaft pulley. You cannot remove the plastic lower timing belt cover unless you remove all of these things first. The sensor is located underneath the lower cover. It has two bolts that hold it in place. You will have to remove these two bolts.

The crankshaft pulling bolt is a right handed thread and loosens by turning counter clockwise. The pulley will slip off but is a very tight fit. Do not try to turn it while removing it as there is a small pin that keeps it aligned to one position. Use a small ball pine hammer to tap it loose.

It is also a good idea to remove the electric cooling fan shroud that is mounted to the inside side of the radiator and the radiator hoses to give yourself more room to work. It has only two bolts at the top holding it in place. And then slips into two retaining clips at the bottom. Lifting it will pull it out of these retaining clips.

When you remove the small bypass hose located at the top of the radiator , to the passenger side, be careful not to break off the small nipple protruding out of the radiator tank. It is plastic and will break easily if you try to pull the rubber bypass hose from it. This will have to be taken to a radiator shop to have repaired if you accidentally break this off. Be sure to carefully loosen the hose from this nipple before trying to pull it off.

And one more thing, if you go to that much trouble to replace this sensor, it is a good idea to go ahead and replace the timing belt as well. It is a maintenance item and you will have to go through the same process to replace it as well. Do it once and do it all.

I hope this helps.

Posted on Nov 15, 2008

Ad
aref_bilal
  • 13 Answers

SOURCE: I am changing the spark plugs on my 2004 Kia sorento

Be careful there.. If you remove the Throttle Position Sensor TPS or the throttle Cable, the engine light will come on because there is a certain setting that needs to be done to ensure accurate emission control.

Posted on Apr 14, 2009

  • 1 Answer

SOURCE: kia sorento, 2004. clock and airbag warning light

You may have a fuse problem.

Posted on Jun 02, 2009

  • 39 Answers

SOURCE: How do you change head lights on a 2004 kia sorento?

The whole headlight assembly needs to be removed from the vehicle to access the lamps inside; especially on the side with the battery (left side).

Remove 3 10m bolts (one on top two on front)

Headlight assembly is held in place wth a large Nylon clip ear outer edge at bottom of the unit. Tilt out at the top and then pull forward and upward to remove. It fels like something's gonna break, but it's pretty tough.

Remove large round cap from behind either high or low beam lamp. Both lamps are hels in with a metal spring clip. Low beam is H-7, high beam is H-3.

To re-install, press bar into Nylon clip and then install 3 10mm bolts. Use a Torx bit to engage gear teeth and adjust height if necessary. There may or may-not be adjusters for left-right alignment.

Posted on Jun 04, 2009

emissionwiz
  • 76846 Answers

SOURCE: Where is the Fuel Filter in a Kia Sorento 2004 LX

THE FUEL FILTER IS IN THE FUEL TANK, THERE IS An ACCESS PANEL UNDER THE REAR SEAT CUSHION.

Posted on Sep 15, 2009

Testimonial: "Had conflicting info about location of it & was skeptical about doing it.Have 2 say it takes some skills 2 not break anything. Was successful, Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why doesn't the license plate light on my 2004 Kia Sorento work ? Tail lights work, back ups,etc, but no license plate light


Have you checked for power to the bulb socket with a voltmeter? Is there a good ground?

Nov 06, 2014 | 2004 Kia Sorento

1 Answer

Trying to figure out if I am having fuel pump problems or possible rear differential problem on 2004 kia sorento. Hearing a whining or moaning when driving more profound mostly when breaking but...


Could be your transfer case, have it check out and lubricated. Did you change tires, or are tires different in size, if just one, tire is different in size, pressure or thread, you can also get this noise.

Jan 28, 2011 | 2004 Kia Sorento

2 Answers

Does the kia sorento 2.5 crdi xe have a timing on a 2004 plate


THE KIA SORENTO HAS 3.3 AND 3.8 ENGINES THEY HAVE TIMING CHAINS.THE KIA 2.4 ENGINES HAS TIMING BELT GUIDE PLATE.

Jun 21, 2010 | 2004 Kia Sorento

1 Answer

Need help getting the axle nut off of 2004 kia sorento nut won't budge


make sure you have a good brand breaker bar(lifetime warranty best), the proper sized socket(impact type), and either an old bumper jack that fits over the breaker bar or a 5 to 6 foot fence post. leave the whole vehicle on the ground, if you cant reach nut with wheel on, then have a helper stomp on the brakes firmly while you put breaker bar at nine oclock, slip jack or post over breaker bar and firmly add your weight and a friends to the end of bar pushing down until SOMETHING gives, hopefully its the nut. :)

Jun 20, 2010 | 2004 Kia Sorento

1 Answer

01 kia optima stalled and wont start...starter just clicks


It seems the starter is playing up.First check if your battery is charged fully or try to jump start and see what happens.If the engine start then it's either you need a new battery or else you need a replacement alternator.Test using a voltmeter if the actual altenator is working.Finally the last option is the starter motor that needs changing or fixing...Hope this helps.

Jul 03, 2009 | 2004 Kia Sorento

2 Answers

CHANGING THE 3 BELTS ON MY 2004 KIA SORENTO


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2004/make/kia/model/sorento/2004_kia_sorento_drive_belt_routing_diagram.htm

Mar 20, 2009 | 2004 Kia Sorento

1 Answer

I need to find a schematic for 2004 kia sorento


I needed one too. Had to go to dealer and buy a manual, is 100.00$ couldn't find one anywhere else

Dec 28, 2008 | 2002 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...