Question about 2001 Ford Explorer Sport

1 Answer

Don't have code for door locks

Need to reset door lock code but don't have factory code

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Look where your jack is and using a flashlight shine it up towards the wheelwell and you will see a set of numbers thats your keyles entry code for your explorer

Posted on Feb 28, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: What is the reset code on the door lock for the

it is stamped on the body of your vehicle usually above the rear wheel well on the drivers side just under and plastic trim (in a wagon its easy but in a sedan its a little tougher to find but it IS there!

Posted on Aug 03, 2009

  • 108 Answers

SOURCE: I just bought a 2002 explorer and need the factory

you need to bring the car to any ford dealer and hook up the diagnostic computer to retrieve the original door code so u can program your desired combination.you cant erase the original factory code but you can add you own only.

Posted on Feb 02, 2010

  • 8404 Answers

SOURCE: i have a 2000 expedition how do i reset my door

You can get this code from your Ford Dealer based on your VIN. Take your VIN, your car and your sweet self along with proof that you own the vehicle to the Service Manager and ask him or her for help.

Posted on Jun 05, 2010

sscullys
  • 984 Answers

SOURCE: My 2006 F-150 drivers side

With the list you have, I would think broken ground wire in the rubber boot from the A-pillar to the door on the driver's side.
I have seen this one a few times ( not chronic but happens ).

It is a black wire in the door to a-pillar harness. SWAG at why the window worked when open part way, the wire touched at that one time, and pulled back apart again.

Example picture of a broken wire
sscullys_216.jpg

Posted on Sep 22, 2011

cansmo
  • 2431 Answers

SOURCE: Just bought a 1999 ford explorer xlt don't have

You need a NGS (Ford factory scan tool) They can access the RAP KEYCODE PID.

Posted on Mar 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Expedition door lock


Replace the battery on the key fob! Also, it may need to be reprogrammed by the Dealer!
Dr. Gene n Landrum

May 19, 2013 | 1999 Ford Expedition

1 Answer

Put a new battery in , now it's not starting and the lights keep blinking


sounds like the alarm needs reset-don't know if it's factory of aftermarket-if you don't have some kinda remote then try closing all doors and lock & unlock driver door with key a couple times

Mar 18, 2013 | 1995 Toyota Camry

1 Answer

How do you reset memory fuse in 2005 kia sorento


No such thing as resetting anything,certainly not a fuse,that is silly just to hear it

You need a dealer to resolve the issues you created & have
them explain how you get the radio & other items working,so you don't do it again

Jun 12, 2012 | 2005 Kia Sorento

1 Answer

Just bought a 1999 ford explorer xlt don't have


You need a NGS (Ford factory scan tool) They can access the RAP KEYCODE PID.

Mar 07, 2012 | 1999 Ford Explorer

3 Answers

Is the anti-theft deterrant system the same system as the engine immobiliser or are they completely different?


Hello Jaclyn... Your Camry has an "engine immobilizer" designed to prevent "hot-wire" starting incorporated into the anti-theft system...This was standard on the XLE, & an available option on the LE. When the battery cable came off the immobilizer lost it's memory & is not reckoning the chip in the key. Try locking and closing all the doors. Then unlock the drivers door with the key. Repeat this several times, also tap the brake & gas pedal. If this does not help the dealer will have to reset it by the vehicles VIN number.
I hope this information is helpful.

Dec 01, 2011 | 1998 Toyota Camry

6 Answers

1994 Saab Areo 9000 power locks will not work therefore cannot open gas door. Tried changing fuse but that didn't work


Check fuse #15 if you have not done so & check in the trunk for a manual over ride under the tool kit. The 90-92 models had one, not sure if your model does. I don't have a lot of info on the 94 A 9000-- Maybe a Saab expert will chime in with more advise.

Sep 24, 2011 | 1994 Saab 9000

1 Answer

I have 98 Camry Le and the door locks lock automatically shortly after the doors are unlocked and the alarm will set also. What could be the problem? Alarm Control Box?


if you use the keyless entry to unlock the vehicle & don't open a door within 30 secs.the vehicle will automatically lock & the alarm will reset,if you unlock it with the key this shouldn't happen.....cheers.

Sep 01, 2011 | 1998 Toyota Camry

1 Answer

My 2000 licolin battery died the key won't open the door lock how do get in to the engin to put jumpers on the battery to give it enough power to work the locks ps i don't understand why the key...


The key has to open the drivers door

Raise the car up,support it,& put your battery
charger on the starter battery cable terminal
& ground the black clip

Try charging the battery for 4 hours or so

Jul 02, 2011 | 1998 Lincoln Continental

1 Answer

Need to reprogram key less entry. 2002 Ford explorer sport.


Keyless Entry Keypad FAQ Ford Explorer
The keypad can be operated with the factory set 5-digit entry code
You can use the keyless entry keypad to
  • Lock or unlock the doors without using a key.
  • Open the liftgate window.
  • Activate or deactivate the autolock feature.

Where the code can be found
  • This code is located on the owner's wallet card in the glove box
  • Is available from your authorized dealer via scan code
  • Is marked on the computer module

Computer Module location
  • 1995 thru 2001 is located in the jack storage compartment in the rear of your Explorer. First remove the panel to the jack storage compartment. Towards the front of this area you should see a metal box this is your auto-lock module(way up front next to your rear left passenger seat). On the back side of this is your 5 digit code factory preset code. It is hard to get to. To see it you will have to loosen, pull, use a flashlight or a mirror but it can be done.

  • 2002 thru 2007 is in the right panel behind the middle row window. It is below the seat belt mechanism. You have to pull out the top plastic panel off, then loosen the lower panel to be able to see the face of the computer module. The code is on a sticker on the face of the module.

Programming a personal entry code The factory set code cannot be reprogrammed but you can create your own 5�digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.
Up to three personal entry codes may be programmed to the vehicle. To create your own personal entry code:

  • 1. Enter the factory set code.
  • 2. Within five seconds press the 1 � 2 on the keypad.
  • 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.
  • 4. Press 1 � 2, 3 � 4 or 5 � 6 to indicate which of the three personal entry code positions you wish to use.
  • 5. The doors will again lock then unlock to confirm that your personal key code has been programmed to the module.
Tips:

  • Do not set a code that uses five of the same number.
  • Do not use five numbers in sequential order.
  • The factory set code will work even if you have set your own personal code.
  • If you program a code to a position that already contains a set code, the previously-set code will be erased.

Erasing personal code
  • 1. Enter the factory set 5�digit code.
  • 2. Within five seconds, press the 1 � 2 on the keypad and release.
  • 3. Press and hold the 1 � 2 for two seconds. This must be done within five seconds of completing Step 2.
All personal codes are now erased and only the factory set 5�digit code will work.

Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after
  • One minute of keypad inactivity.
  • Pressing the UNLOCK control on the remote entry transmitter.
  • The ignition is turned to the 3 (ON) position.

Unlocking and locking the doors, liftgate and liftgate window using keyless entry
  • To unlock the driver�s door, enter the factory set 5-digit code or one of the vehicle�s personal codes.
  • Each number must be pressed within five seconds of each other. The interior lamps will illuminate.
  • To unlock all doors and liftgate, press the 3 � 4 control within five seconds.
  • To open the liftgate window, press the 5 � 6 control within five seconds.
  • To lock all doors, liftgate and liftgate window, press the 7 � 8 and the 9 � 0 at the same time.

  • Note: The driver�s door must be closed. You do not need to enter the keypad code first.

Deactivating/activating autolock
  • Your vehicle comes with the autolock feature enabled.
Note: The autolock feature can be activated/deactivated independently of the autounlock feature.
Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is in the 1 (OFF/LOCK)position, and all vehicle doors, liftgate and liftgate window are closed.
*Keyless entry key pad procedure

  • 1. Turn the ignition to the 1 (OFF/LOCK) position.
  • 2. Close all doors, the liftgate and liftgate window.
  • 3. Enter 5�digit entry code
  • 4. Press and hold the 3 � 4. While holding the 3 � 4 press the 7 � 8.
  • 5. Release the 7 � 8.
  • 6. Release the 3 � 4.
The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.
Autounlock The autounlock feature will unlock all the doors when: � the ignition is in the 3 (ON) position, all the doors are closed, and the vehicle has been in motion at a speed greater than 12 mph (20 km/h); � the vehicle has then come to a stop and the ignition is turned to the 1 (OFF/LOCK) or 2 (ACC) position; and � the driver door is opened within 10 minutes of the ignition being transitioned to the 1 (OFF/LOCK) or 2 (ACC) position.
Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened.

Deactivating/activating autounlock - Keyless entry key pad procedure Your vehicle comes with the autounlock feature activated.

  • 1. Turn the ignition to the 1 (OFF/LOCK) position.
  • 2. Close all doors, the liftgate and liftgate window.
  • 3. Enter 5�digit entry code
  • 4. Press and hold the 3 � 4. While holding the 3 � 4 press the 7 � 8 twice.
  • 5. Release the 7 � 8.
  • 6. Release the 3 � 4.
The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.
The keyless entry touch pad can use two codes. The factory code and one
personal code .
To program your own personal code, select a 5 digit code that doesn't use 5 digits in
sequence or the same button 5 times.
Enter your factory code
Within 5 seconds press the 1/2 button
Within 5 seconds of pressing the 1/2 button, enter your 5 digit personal code,
pressing each digit within 5 seconds of the previous digit.
You can now use either code to operate the keypad

Setting FOB to work with your vehicle
  1. Sit in car, doors closed. Electronically unlock all doors using the power door unlock switch on the driver's door.
  2. Insert key into ignition switch and turn from OFF to ON 8 times within 10 seconds with the 8th time ending in the ON position. (5 times on some models)
  3. The doors should lock and unlock by themselves to signal programming mode.
  4. Using your remote: lock the doors.

Sep 16, 2009 | 2002 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...