Question about 2001 Toyota Sienna
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I just replaced my left rear brake light on my 2005 Sienna. I followed the manual directions and removed the two metal bolts from the tail light cover. However the assembly did not come off. I could open it a little and it appeared to be bolted from the inside. I looked online but didn't find an answer. I had already gotten pulled over and I didn't want to go to the dealer so I pulled on the assembly a little harder applying even pressure to the top and the bottom and it popped loose. I didn't yank it. There are two metal pegs that have a little lip on them and thats where you are getting the resistance. Hope this helps.
Posted on Jan 11, 2009
You gotta flip the wiper arm up, and turn the blade out. Underneath you will find a tab in the center. Press in on this tab and slide the blade out.
Posted on Jan 25, 2009
this sounds correct, however, if you go to autozone.com, the have access to free online manuals, giving you step by step instructions on how to remove. you will need to register and provide some info about your vehicle. it is FREE! the manuals are in the do it your self area. Good Luck!
Posted on Sep 13, 2009
Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.
Remove the bolt and the strap/
Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.
Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.
Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.
Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)
The license plate trim panel, should you need to remove it, requires remoaval of the license plate.
Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.
Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)
Posted on Sep 20, 2009
Testimonial: "Very helpful. thanks"
SOURCE: back door panel removal
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls
Posted on Sep 23, 2009
Tips for a great answer:
Nov 29, 2015 | 2005 Toyota Sienna LE
Nov 11, 2013 | Toyota Cars & Trucks
Mar 19, 2013 | 2006 Toyota Sienna
Jul 16, 2011 | 2000 Toyota Sienna
Mar 06, 2010 | 2001 Toyota Sienna
Nov 09, 2009 | 2007 Toyota Sienna
Nov 29, 2008 | Toyota Sienna Cars & Trucks
Oct 26, 2008 | 2001 Toyota Sienna
Jul 29, 2008 | 2006 Toyota Sienna
82 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: