Question about 2000 Dodge Durango

Open Question

P1391 code on a 2000 Dodge Durango with 5.3L engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: dodge caravan 1997 3.3l Xavierfrancofuenmayor

Had similar problems occur on various Chrysler products manufactured since 1986. What I did was remove the computer from the car and then take a Dremel tool with wire brush attachment and lightly buff all the pins of the computer--tops, sides and backs. After this I then take a jewelers round file and insert the tip into each connector pin hole and very lightly file it to remove any corrision. When I reassembling the connector plug to the computer I placed a good size dab of silicon grease on the plug in the center (acts as a seal when seated). This has eliminated the problem on four different vehicles.

Posted on Aug 28, 2008

  • 1 Answer

SOURCE: I have a 2000 dodge durango, I have a code P0320.

I put in a new crank positioning sensor and it fixed my problem. 42.00 dollars from NAPA. took about 2 hours to change it.

Posted on May 02, 2009

  • 2 Answers

SOURCE: Why is my engine light on on my 2000 Dodge

you need to put your key in the ignition turn til dash lights come on dont start engine then turn it off ,do this 3 times leaving key in the power position on the 3rd time, watch your speedo and check the codes . p0700 is a tranny problem,you dont need to get it scanned at a dealer unless you need to 95% it is the speed output sensor 5 minute fix under 100 buks do it yourself. any other code check it and go on the internet cuz alot of people get ripped off and its a simple cam sensor , crank, abs, speed,etc....

Posted on Aug 09, 2009

  • 8 Answers

SOURCE: 2002 Dodge Durango 4.7L V8 Check Engine Codes

1st try and search for a vaccum leak, due to the fact that these vehicles have had some bad problems with the length of wires and hoses, if there is a vaccum leak in the vehicle somewhere that will trigger other malfunctions in your vehicle. Using a can of starting fluid or Brake cleaner spray lightly spray around our engine til you hear the motor rev-up and the spot you have sprayed will determine where your vaccum leak will be. And then check under your distributor cap for any moisture be sure to take a rag and wipe and residue off. Also check the firing order on your distributor.

Posted on Oct 28, 2009

  • 1 Answer

SOURCE: Engine Code P0505

After the IAC is replaced it is not enough to clear the code you must also reset the IAC learned adaptive. To do this you will need a higher end scanner like snap-on or such.

Posted on Jun 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2000 durango4.7 was driving home last night it died threw up code p1389 I have seen a power steering leak and it leaked on a sensor would this cause it not to run


I wouldn't think so , these sensors are made to be in a harsh environment ! If fluid or oil soaked for a long time , it could affect the wiring , maybe ! Your problem is the code , crankshaft sensor and or cam sensor ! P1391 DODGE

Apr 08, 2015 | 2000 Dodge Durango

1 Answer

My car reading the following codesp1489 codep0601 p0725 p1490 p1391 p0700 p 0703,car cut off while driving oil seems to be thin smells a Lil like gas was told its a sensor but not which one Let me know any...


If the oil smells like gas , pull the dip stick an put a lighter to it ! If it catches fire there is gas in the oil ! you don't won't to drive the car it could explode ! .
P1391 is for camshaft position sensor and crankshaft position sensor. the code is for either sensor or both

Read more: http://engine-codes.com/qa/4492/p1391-dodge#ixzz3TS85EkNt
P1489 Dodge - High Speed Radiator Fan Control Relay Condition

Read more: http://engine-codes.com/p1489_dodge.html#ixzz3TS8ycHqw
P1490 Dodge - Low Speed Radiator Fan Control Relay Condition

Read more: http://engine-
codes.com/p1490_dodge.html#ixzz3TS9QKO2x

P0725 Dodge - Engine Speed Sensor Circuit
P0700 Dodge - Transaxle Control System Malfunction
P0703 Dodge - Brake Switch Performance Repair Importance Level: 3/3 Repair Difficulty Level: 2/3 help.jpg pdf.gif share.png 2 0 comments.png ' Add Comment xicon.jpg http://engine-codes.com/p0703_dodge.html Forum Code Possible causes - Faulty Brake Switch
- Misadjusted Brake Switch
- Brake Switch harness is open or shorted
- Brake Switch circuit poor electrical connection

Read more: http://engine-codes.com/p0703_dodge.html#ixzz3TSAXHIBZ
With all these codes present , without looking under the hood , I would think you have a wiring harness problem ! I have seen critters make nests in the engine compartment , they like to chew wiring ! Have seen air filter boxes full of dog food . Good luck your going to need it !

Mar 04, 2015 | Dodge Cars & Trucks

1 Answer

Code p1391


You could've gotten dirt or grease inside the cam sensor connection. They are real fussy.

Jun 07, 2017 | 2000 Dodge Ram 1500 Truck

1 Answer

Fix a p1391 code


Timing belt or chain stretched or jumped
- Faulty Camshaft Position (CMP) Sensor
- Camshaft Position (CMP) Sensor harness is open or shorted
- Camshaft Position (CMP) Sensor circuit poor electrical connection.

Read more: http://engine-codes.com/p1391_chrysler.html#ixzz3GJfh5IpX

Mar 24, 2014 | 2000 Dodge Durango

1 Answer

P1391


P1391 Glow Plug Circuit Low Input (Bank #1)
__________
volvo dice

Mar 19, 2013 | 1998 Dodge Durango

1 Answer

Code P1899 2000 Dodge Durango


try to reset.but if not why shows code.

Feb 24, 2013 | 2000 Dodge Durango

2 Answers

I HAVE A 97 DODGE RAM 1500 V8 AND ONE CODE CAME UP A P1391 CODE I NEED TO KNOW WHAT IT IS


P1391 DODGE - Electronic Brake control Rough Road Data Unusable/unreadable
You need to see the dealer on this, it may be programing issue.

Nov 07, 2012 | Cars & Trucks

1 Answer

What does the p1391 code on a 99 dodge ram 1500 5.2l v8 meen


check engine light and code P1391 crank or cam position sensor

The above can cause rough idle on the Dodge Ram 1500 5.2L V8 Engine.

Can try to replace the sensor, but verify that the wires are ok first.

Aug 12, 2010 | Dodge Pickup Cars & Trucks

2 Answers

2002 Dodge Durango 4.7L V8 Check Engine Codes


1st try and search for a vaccum leak, due to the fact that these vehicles have had some bad problems with the length of wires and hoses, if there is a vaccum leak in the vehicle somewhere that will trigger other malfunctions in your vehicle. Using a can of starting fluid or Brake cleaner spray lightly spray around our engine til you hear the motor rev-up and the spot you have sprayed will determine where your vaccum leak will be. And then check under your distributor cap for any moisture be sure to take a rag and wipe and residue off. Also check the firing order on your distributor.

Oct 28, 2009 | Dodge Cars & Trucks

2 Answers

Fault Code- 2000 Dodge Durango


govoner psi too high. as to what this truely means, im not sure

Jul 14, 2008 | 2000 Dodge Durango

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...