Question about 2005 Dodge Neon

Open Question

Where is EGR VALVE in 2005 dodge neon - 2005 Dodge Neon

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BCally1
  • 133 Answers

SOURCE: How do I change a EGR Valve on a 2005 Dodge Magnum STX w/3.5 engi

its a pain in the *** but it located on the right rear (pass. side) of the motor. it bolts to the cylinder head and runs up to the intake manifold

Posted on Jan 09, 2009

  • 1596 Answers

SOURCE: 2005 Dodge 1500 code p0404 EGR valve.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Posted on Feb 05, 2009

  • 1 Answer

SOURCE: Replacing the EGR valve on a 2004 Dodge Caravan 3.3L engine

I repair mine last summer,
It is on the exast port, left.
You have a tube attach to it, going in the Head Cover.
Easy to change. it cost me $105.00CND at the dealer

Good Luck
Jonathan Lévesque

Posted on Feb 28, 2009

  • 116 Answers

SOURCE: egr valve dodge durango

if this is a 4.7l engine, the valve is on the left rear of the intake. loosen the 8mm bolts that hold the egr intake tube to the egr valve, remove the egr bolts, disconnect wiring, remove valve and tube together, attach intake tube loosely to new valve, install new valve, tighten tube bolts to egr using a swivel socket, this is not a 5 minute job, so dont attempt unless you have some time and patience.

Posted on Apr 24, 2009

ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 98 neon that needs o2 sensor and egr valve fixed. Ive been quoted 340 repair bills for the work. Is that reasonable, or better to put 700 down start payments on a new car?


Carlos, Can you do any work your self new EGR valve $50.00, new O2 sensor $50.0 or less ordered through Rock auto.com, if car overall in good shape may be worth fixing. Especially if finances are tight. get a second even third estimate and this time ask them if you supply new parts O2 and EGR how much they want for labor, should not be more then 1.5 hours. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Upstream Oxygen Sensor Replacement Dodge Neon EGR Valve Replacement Cost for Dodge Neon RepairPal Estimate
how to clean an egr valve
Oxygen Sensor Replacement Cost RepairPal Estimate

Apr 28, 2016 | Cars & Trucks

1 Answer

I have a 96 dodge neon. when it gets to 1000 rpm's or lower it stalls out. i got a new fuel filter. there are no leaks in the hoses. what could be the problem?


your problem may be a bad iac ( idle air control ) valve. also check or clean egr valve passage way to engine. or the egr itself is stuck open. ( exhaust gas recirculation ) valve.

Aug 25, 2010 | 1996 Dodge Neon

1 Answer

2005 dodge caravan diagnostic code p0404, please explain and do i replace the egr valve?


p0404 is-egr flow ckt range/performance, check egr, remove from vehicle and clean out carbon from valve and where it mounts on engine. also check the wireing connector and wire to valve. if this dosnt work, replace valve,

Apr 23, 2010 | 2005 Dodge Caravan

1 Answer

Where is the egr valve on a 2005 dodge 1500 5.7L


The electronic EGR valve and solenoid assembly (3) is attached to the front of the right cylinder head (1). An exhaust gas routing tube connects the EGR valve to the intake manifold.

2efe0f8.gif

Disconnect electrical connector (1) from EGR solenoid (2). Remove two bolts (3) connecting EGR tube (4) to valve assembly. Remove gasket located between EGR tube flange and EGR valve assembly.

Remove two mounting bolts (2). Separate valve assembly (3) from cylinder head (1). Remove and discard metal gasket located between cylinder head and valve assembly.
The new EGR valve will come with a new metal gasket. You can reuse the smaller gasket for the metal pipe going to the egr valve as long as its not damaged.

TY for using Fixya; remember rated this post.

Apr 14, 2010 | 2005 Dodge Ram 1500

1 Answer

1998 Dodge Neon, has code: PO403, EGR circuit malfunction, where should I be looking? Thanks.


egr valve is located near exhaust manifold...exhaust gas recirculation or egr valve ports some exhaust fumes back to the inlet manifold in order to meet emmissions requirements...so look in this area

Nov 09, 2009 | 1998 Dodge Neon

1 Answer

2005 dodge grand caravan getting code p0406


3.3 engines has the egr valve with transducer.you have to replace the whole unit. code p0406 what its trying to tell you your egr valve circuit is short to ground.it has failed .

Jul 04, 2009 | 2005 Dodge Grand Caravan

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

1 Answer

2002 DODGE NEON RUNS RUFF AT IDLE


Engine light on? sounds like EGR valve the cross pipe from EGR to air intake plugs causes them to idle rough if eng light not on soon it will surface! good luck hope this helps!

Sep 09, 2008 | 2001 Dodge Neon

Not finding what you are looking for?
2005 Dodge Neon Logo

Related Topics:

896 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...