Question about 2002 Ford Escape

1 Answer

Seat bealt light on but my seat bealt is working

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Reset the connector under the Pax. side front seat. This has to be done with the ignition off. 1. Buckle the seatbelt. 2. Reset connection. 3. Unbuckle the seatbelt. 4. Turn ignition switch on and watch the light reset to off. 5. If light continues off, go to the Driver side and repeat the procedure. My problem was fixed after doing procedure 1. hope that helps.

Posted on Jan 23, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Seat belt light stays


Pull on the belts out a few times
& see if the light goes off

Aug 21, 2014 | 2002 Chevrolet Impala

1 Answer

I have a 2002 ford escape, the engine light has been on for some time, no code was detected when put on the machine, I just had the coils replaced and started noticing problems when the ac was on, the...


Having problems with the dash will cause all kinds if problems, like your having. Ford decided to put the Instrument panel, body control module and security all in the IP.First thing I would do is pull the IP Check the wires and plug going to it. Make sure you put it back in and it is a snug fit. You can also have a diagnostics done on this. IP, BCM, Security codes don't always show up on the ECM.

Jun 28, 2011 | 2002 Ford Escape

1 Answer

Bealt


More detail please. What bealt? where is it from? etc...

Jun 11, 2011 | 1992 Jeep Wrangler

1 Answer

I need a picture on how to put the bealt back on my 1994 caravan


You not going to find that on the internet,
unless you just get lucky or see it on You Tube

Ask a friend or neighbor for help

May 24, 2011 | 1994 Dodge Caravan

1 Answer

Repair Isuzu Rodeo 2001 Timing Bealt


I suggest you get a mechanic to put it on . This job is not for a novice parts replacer.

Jan 10, 2011 | Isuzu Rodeo Cars & Trucks

2 Answers

My son's 1995 Oldsmobile Cutlass won't start one morning. Lights still on in car and radio. It wasn't the battery and triple AAA suspected it needed not starter. This was replaced. Then still won't start...


does it act like it wants to start or just clicks an there may be a fuse that is blowin. or worst case seniro time an chain gears/timeing bealt jump or just a bad starter relay

Nov 17, 2010 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Car was after accident and the seat bealts are locked . they wont move at all. do i rest the computer or is there another way?


By U S law the seat belts are not repairable. Only to be replaced. You can pry the housing open to see what the problem is although they are very complexed inside

May 26, 2010 | 2005 Pontiac Vibe

2 Answers

Diagrams for changing timing bealt


What engine do you have?

Need to know to get the the proper diagram.

Nov 08, 2009 | 1998 Dodge Intrepid

1 Answer

Rear seatbelt


fold rear down take outter seat off one twelve bolt at bottom remove clps and pck tray YOU GOT IT

Mar 07, 2009 | 1997 Toyota Camry

2 Answers

2005 toyota corolla airbag light problem


Sounds like your mechanic installed something per your request. Unfortunately, you have to order the specific part for your vehicle or the light will stay on because the vehicle computer is not detecting a secong airbag.

Feb 11, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
2002 Ford Escape Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...