Question about 2002 Nissan Altima

Open Question

2002 nissan altima loses power going up hill

Trys stalling when stopped and looses power going up hill

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jschoon77
  • 55 Answers

SOURCE: DOOR WON'T OPEN FROM INSIDE OF NISSAN ALTIMA 2002 ON DRIVER'S SIDE

There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.

Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.

Hope this is helpful!!



Nissan Scope Technician- 10+ years experience in Nissan dealership

Posted on Nov 11, 2008

Ad
  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 54 Answers

SOURCE: Tune up nissan altima 2.5L model 2002

All you really need is a good set of spark plugs, this car has coil packs so no plug wires distributor caps etc.....Just remove the coil packs and install your plugs and your done. Good luck.

Posted on May 31, 2009

  • 1 Answer

SOURCE: 2001 Nissan Altima - Instrument panels gauges stop working

My 2001 Altima's instrument gauges die out after high-speed driving for 40-50 miles. Engen also loses power. Everything is back to normal when the car cools down. It turned out the ingition relay was bad. I could duplicate the problem right away by removing the relay. Actually, it is very easy to find the relay which is located above the fuse panel. The ignition relay is the bottom left one among the five relays there. It costs only $20.

Posted on Nov 13, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Lose of powe up hill no warning lights and idle is good


Fuel filter air cleaner filter plugged or need a tune up or air sensor in intake line put on computer will tell you right away if you want

Jan 12, 2016 | 2004 Nissan Altima

1 Answer

Hesitate or stall when stop and go on up hill


Sounds like the fuel pump is going out.

Mar 16, 2015 | 2000 Nissan Altima

1 Answer

2001 nissan altima loses power while driving.


Sounds like you may have a wire heating up and grounding out or a wire loosing contact.

Apr 13, 2013 | 2002 Nissan Altima

1 Answer

1998 Nissan Altima is stalling at red lights and stops


Referring you to hubby, an excellent mechanic. We have Altimas. He will help you. dkwood163@yahoo.com

Aug 27, 2017 | 1998 Nissan Altima

1 Answer

We have a nissan 2002 altima that looses power going up a bit of a hill. It starts ok but the battery doesn't keep the charge and the altinator has been replaced. No power when stepping on the gas...


Please check the throttle valve connections and make sure it's working properly.Since there is no power gain during hill climb, the desired torque is not achieved due to excessive wear of gear tooth or due to the problem with the clutch plate.Please make sure these are properly working.

May 29, 2011 | 2002 Nissan Altima

1 Answer

How do I get to the rear Speaksers of a 2001 Nissan Altima to remove and replace? (They are located on the rear window back panel)


Good morning, I own a 2001 Nissan Altima. When I run my AC and stop, or put it in reverse, my car stalls. I would just turn off my AC, but now when I am on the Interstate it tends to "pull" like if i was losing power.

Jul 22, 2010 | 2001 Nissan Altima

1 Answer

1994 Altima


Did the car stall out? If the car stalled out she would have had to step hard on the brake to get the car to stop. When a car stalls you loose the power brakes causing most people to panic and step too hard on the brake causing them to lock up. If the car overheated there should be an inactive code in the ECM. Bring the car to an Auto Zone and they will scan your ECM for free. Good Luck!!

Sep 23, 2009 | 1994 Nissan Altima

2 Answers

2003 Nissan Altima stalls at intersections/ stops


sounds like your carb is getting to much air some where check your hoses

Sep 20, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
2002 Nissan Altima Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...