Question about Hyundai Cars & Trucks

Open Question

How do you replace front brake pads on a 2005 hyundai xg350

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: how to replace rear brake pads on 2005 jeep liberty

put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Posted on Mar 01, 2009

  • 2 Answers

SOURCE: replace front brake pad 2003 toyota 4 runner

Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers

Posted on Mar 25, 2009

  • 67 Answers

SOURCE: change brakes on a 05 hyundai tucson

rear pad replacement is basically the same as front. 14mm bolts holding caliper and mount on hub then the piston just pushes in

Posted on Apr 09, 2009

tse22
  • 103 Answers

SOURCE: Changing Rear brake pads 2005 dodge grand caravan

There are 2 bolts on the "inside" on the caliper towards the bottom they use an allen wrench socket.

Posted on May 13, 2009

c17hydro
  • 2984 Answers

SOURCE: I need 2004 Hyundai XG350L Service/repair Manual

3.5L Engine

Remove or disconnect the following:

  1. Negative battery cable
  • Engine coolant
  • Water pump pulley bolts
  • Alternator bolt, loosen only
  • Water pump pulley and drive belts
  • Crankshaft pulley
  • Timing belt cover(s)
  1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
  2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
  3. Mark the timing belt with an arrow showing direction of rotation.
  4. Remove the timing belt.
  5. If defective, remove the timing belt tensioner.

9767b45.gif
Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

To install:
  1. If necessary, install the timing belt tensioner.
  2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
  3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
  4. Align the timing marks of the camshaft and crankshaft sprockets.
  5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
  6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
  7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
  8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
  9. Turn the crankshaft two turns clockwise.
  10. Readjust the sprocket timing marks and tighten the tensioner bolts.
  11. Install the timing belt covers.
  12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
  13. Install or connect the following:
    • Timing belt cover(s)
    • Crankshaft pulley
    • A/C compressor belt
    • Water pump pulley
    • V belt
    • Negative battery cable
    • Engine with coolant

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

What you need to know about Hyundai


I am a mechanic ..most people ask questions about these foreign hyundai motors ..below is an example of engines that basically if you ask about a Hyundai Xg 350 ,xg300 ..well allow me to hammer 90% of your questions in case you want to grab another motor ..these motors listed will work on 90% of all hyundai products ...Look at the starter sizes ,,all the same for the selected models ..then look at the motor sizes ..This will help you in solving some problems most do not give the specific questioning
100% NEW REPLACEMENT STARTER
FOR
STARTER

12 VOLT / CW ROTATION / 8 TOOTH DRIVE

REPLACES:
MANDO M62957
VALEO TM000A14401
BOSCH REMAN SR4118X
BOSCH NEWMAN SR4118N
HYUNDAI 36100-37210

FITS ON:

HYUNDAI
2001 SANTA FE 2.7L ENGINE
2002 SANTA FE 2.7L ENGINE
2003 SANTA FE 2.7L ENGINE
2004 SANTA FE 2.7L ENGINE
2005 SANTA FE 2.7L ENGINE
2006 SANTA FE 2.7L ENGINE

2003 SANTA FE 3.5L ENGINE
2004 SANTA FE 3.5L ENGINE
2005 SANTA FE 3.5L ENGINE
2006 SANTA FE 3.5L ENGINE

2002 SONATA 2.7L ENGINE
2003 SONATA 2.7L ENGINE
2004 SONATA 2.7L ENGINE
2005 SONATA 2.7L ENGINE

1999 SONATA 2.5L ENGINE
2000 SONATA 2.5L ENGINE
2001 SONATA 2.5L ENGINE

2003-2008 TIBURON 2.7L ENGINE

2005-2008 TUCSON 2.7L ENGINE

2001 XG300 3.0L ENGINE

2002 XG350 3.5L ENGINE
2003 XG350 3.5L ENGINE
2004 XG350 3.5L ENGINE
2005 XG350 3.5L ENGINE

KIA
2004 AMANTI 3.5L ENGINE
2005 AMANTI 3.5L ENGINE
2006 AMANTI 3.5L ENGINE

2001 MAGENTIS 2.5L ENGINE

2002-2006 MAGENTIS 2.7L ENGINE

2001 OPTIMA 2.5L ENGINE

2002 OPTIMA 2.7L ENGINE
2003 OPTIMA 2.7L ENGINE
2004 OPTIMA 2.7L ENGINE
2005 OPTIMA 2.7L ENGINE
2006 OPTIMA 2.7L ENGINE

2002-2005 SEDONA 3.5L ENGINE

2005 SPORTAGE 2.7L ENGINE
2006 SPORTAGE 2.7L ENGINE
2007 SPORTAGE 2.7L ENGINE
2008 SPORTAGE 2.7L ENGINE

on Oct 24, 2013 | Hyundai Cars & Trucks

1 Answer

Alarm randomly going off remote will turn itboff but few mins later starts again


Hyundai XG350 alarm module Questions & Answers - Fixya

www.fixya.com > ... > Tags > alarm module > Cars & Trucks > Hyundai
Hyundai XG350 cars & trucks alarm module questions and answers. Ask your Hyundaialarm ... TURN IGNITON TO ON 4. WAIT 5 ... Hyundai Motor 2005 XG350.

Aug 27, 2015 | Hyundai Motor 2005 XG350

2 Answers

How do you replace the rear bearing hub assembly on a 2003 hyundai xg350?


Could be the same like front,can be four bolts,go to parts store ask for bearings you will see,same cars has no hubs.

Oct 27, 2014 | 2003 Hyundai XG350

1 Answer

Hyundai accent 2005 when starting up the vechile and driving there is a constant ugly sound coming from the front passenger side wheel and when applying the brakes on there is a high pitch squeel


That screeching sound is a warning that your brake pads are worn down to the point where they should be immediately replaced. If you do not replace the pads, you'll score the rotor and incur an additional expense. Remember to replace the brake pads on both sides, i.e., driver and passenger side.

May 01, 2012 | 2005 Hyundai Accent

1 Answer

Cannot get the front tires to come off to change the brake pads!


Take a big hammer, or use the blunt side of an axe, and hit the tire in, toward the car. It should break loose.

Jan 24, 2011 | 2002 Hyundai XG350

2 Answers

Need to replace wheel stud on hyundai sonata, how?


have a 2005 hyudai tucson can't remove the front studs even though we pulled off the brakes and caliper but still not enough room to put in new studs and i can't dissasemble it any further

Aug 15, 2009 | 2002 Hyundai XG350

1 Answer

Clunking coming from back of my 2005 XG350 when going over bumps, and front shocks creak when pushed up or down of front of car..


how it sounds that your muffler is loose or your bushings are wore out on your shocks. then front it could be your shocks or your bushings on the front suspinsion is getting weak or the ball joints need to be greased or replaced.

Jun 09, 2009 | 2002 Hyundai XG350

1 Answer

Need to change pully


Which One?
60a96c9.jpg The one on the left has two 14mm fasteners 1 nut & 1 bolt. The one on the right has the same 1 14mm nut and 1 14mm bolt. Both are simple to replace. Step 1: Relieve the tension on the pully you wish to replace. Step 2: remove the pully (front) by removing the 14mm nut. To remove the rear tensioner pully, remove both nut & bolt.

May 19, 2009 | Hyundai Motor 2005 XG350

1 Answer

Instructions for replacing the front brake pads-2005 Hyundai Tucs


Jack the front of the car up, and make sure it is securely supported. Remove the wheel, remove the 2 guide bolts (located on the back of the caliper), and remove the caliper, hanging it by a coat hanger or wire to keep pressure off the brake line. Remove the pads and shims. Clean rotor with brake parts cleaner, and install new pads/shims. Repeat on other isde. Check with the parts store to see whether or not you need to use anti-squeak compound for your specific brake pads. Once you install them, you will need to bed the brakes to get the most use out of them. Accelerate to 30mph, then hard brake to zero (5-10 times), then repeat but to 60mph and hard brake to zero. Do this a couple times, and you will get very long life out of your brakes.

Apr 16, 2009 | 2005 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...