Question about Cars & Trucks

Open Question

Front wheel bearing keeps on failing on my mazda 323 rustler pickup

I have 17" mags on my car and some say thats the problem but i dont think so the front wheel bearings last about a mounth i have done every thing i can think of please help or tell me where i can get bigger and stronger hubs for my car

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: mazda rustler 160i wheel bearings

a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Posted on Dec 17, 2008

  • 2 Answers

SOURCE: 1997 mazda rustler 160i wheel bearings

buy a chevy

Posted on Dec 19, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Video of how to replace rear wheel bearings of a Mazda 323, 1.3,sting,front wheel power

take the rear hub off
you will need a hydraulic press or a vice to push bearing out and then in.

Jul 09, 2016 | Mazda Cars & Trucks

1 Answer

Where can i get the lefthand side stabaxle for mazda 323 i60i

I take it that you are in the USA where the LH wheel hits the curb What ever it is of little consequence as it is a small problem that will damage the bearings. Wheel bearings fail because of 2 items that most important. First is grease and the second is adjustment. Over greasing or under greasing will cause premature failure. You need a high temperature operating grease to handle the heat generated by the disc brakes. Second if you have taper roller bearings then the correct adjustment is a no preload -no end float position. If the bearings are thrust ball bearings then the spacer between them gives the correct adjustment Ensure that the grease seal in the hub is in the right way to retain the grease

Nov 08, 2013 | Cars & Trucks

1 Answer

Front wheel bearing torque specs on a mazda 323

Call your local dealer PARTS department - they have the spec's in their computer system..
Best regards

Jul 17, 2012 | 1988 Mazda 323 Hatchback

1 Answer

Squeak coming from clutch right at the joint to the plate, there are 2 rubber boots here can this be greased to eliminate the noise-1999 mazda 323

I will assume you are talking about the ****** clutch,i dont think they made a 1999 mazda 323 unless in another country but anyway the noise you are hearing sounds like the pressure plate throwout bearing, this means the bearing is going bad, you must be careful as the grease will get thrown around and end up on clutch plate and cause slipping. if you can you can try spraying a little white lube into the bearing, and on ****** housing to help it slide better also. let me show you a picture of it and where to lube the bearing if theres room. sometimes the boot can be removed and there room to get to bearing, hope this helps.johnjohn2_140.jpg

Sep 24, 2011 | Mazda 323 Cars & Trucks

1 Answer

Mazda 323 how I get the hub of on the front wheel to change the bearing. Warming up to get it of ???

Let's make sure you got the correct wheel bearings.

1.57 in. bore;
2.91 in. outer diameter;
1.57 in. width;

These bearings require a 2 ton press and the correct size die to remove and install.

Some shop can do the job for $20 a pair.

Sep 05, 2011 | 2001 Mazda Protege

2 Answers

I have replace the clutch on my rustler but it

Bleed the hydraulic system. Check the hydraulic lines, it could be swelling, Did you change the pilot bearing as well? If it was removed and not replaced, there will be a hard vibration.

Feb 18, 2010 | 1989 Mazda 323

1 Answer

How do i install front wheel bearings on my 1994 mazda 323

They are pressed in. It might be easyer to buy spendal assembly if you doing it in the drive way.Need a press to push them out and back in with the new.

Jul 22, 2009 | 1994 Mazda 323

1 Answer

Mazda rustler 160i wheel bearings

a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Dec 03, 2008 | 1997 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides