Question about Cars & Trucks

Open Question

1993 ford ranger torque converter solenoid how replace

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 76 Answers

SOURCE: My 2001 Dodge Ram 1500

For a few years, at least in my area, there was a issue with the tcc solenoid. It involved not only replacing the solenoid( dropping the pan and unbolting from the valve body) but also flashing or updating the control module.once both repairs are complete you should have no problems. A good dealer will help you out.

Posted on Dec 06, 2008

  • 1 Answer

SOURCE: jeep codes location of unit

Got me a complete manual for 199 jeep factory model and found location of each individual unit in question. Manual gives u possible solution to each code and repair and or replace. As a mechanic myself testing, trouble shooting and repair was not that difficult. Shift solenoid was very difficult to get to. Located under the head lamp passenger side.

Posted on Nov 19, 2008

  • 132 Answers

SOURCE: Locationof the Torque Converter Clutch Solenoid

Your transmission should still work if the solenoid goes bad. It will just shift funny

Posted on Jan 30, 2009

c17hydro
  • 2984 Answers

SOURCE: torque specifications for 1998 ford ranger

Okay...here is a list since no motor size:

2.5L----- 56-64

3.0L----- 56-64

4.0L----- 59

5.0L----- 75-85

All in ft lbs.......this is for the flywheel.

Posted on Apr 05, 2009

  • 22 Answers

SOURCE: 2001 Cadillac Deville TCC PWM Solenoid Circuit (p1860)

it should take approximately 4 - 5 hours plus the cost of sensor

Posted on Aug 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3,0L Ford ranger 91 want shift into over drive.did before I pulled trans to replace rear main seal in Truck.please help


Overdrive is engaged with a torque convert clutch lockup. ATF travels through the splined shaft on the transmission to the torque converter. Check the seals on the converter and the trans.

Aug 25, 2015 | Ford Cars & Trucks

1 Answer

2010 Ford ranger, slips out of gear (from drive to OD) NO check engine light NO code, New filter and oil ( 2.3 automatic ).


Could be TCC solenoid, sticky valves/ valve body, or torque converter. Could be clutch bands also. Needs to be on a scanner.

May 22, 2015 | 2010 Ford Ranger

1 Answer

Torque converter clutch stuck on


The torque converter clutch solenoid is controlled by the TCM so run the fault codes first/. If you take the solenoid out of the system there is every possibility that the vehicle will not move and if it does the economy will be crap. Best fix the thing properly to start with.

Feb 17, 2014 | Ford Ranger Cars & Trucks

3 Answers

My Ford Focus 2006 4 cyc has an engine code PO741 on my OB2. What does that mean?


P0741 Torque convertor clutch circuit failure,it is located in the transmission valvle body, it is attatch to the valve body you can remove it seperately as long as your going to own the Ford focus you might as well get use to replacing these all the time,very common transmission issue with todays car. By the way it is sensitive to worn transmission fluid,when you dont service often these are suspectable to failure.

Apr 22, 2011 | Ford Focus Cars & Trucks

1 Answer

After my 94 ranger heats up, about 3-4 miles, it starts runniing very rough and stalls when I decelerate


Your torque converter lock-up solenoid is sticking in the "Locked-up" position.

When you accelerate past 1st gear (into 2nd), your transmission "locks-up" to the engine

Apr 17, 2011 | 1994 Ford Ranger Supercab

1 Answer

Torque converter locks up and wont release until it cools off


U may need to replace the torque converter and the torque converter clutch control solenoid inside the transmission it is mounter to the valve body, there is one thing you can try 1st, change the fluid in the transmission and the TCC (Torque Converter Clutch) solenoid, use the new GM spec DEXRON VI transmission fluid, there is a good chance you can fix this by doing these cheaper service and part replacement, if that doesn't work the tranmission must be removed and the torque replaced

May 22, 2010 | 1993 Pontiac Grand Am

1 Answer

1993 ranger sputters until warm?


replace the Oxygen senson before catalytic converter this sensor tells the computer to send signal to fuel injectors to allow rich mixture upon start up for warm up then leans out mixture as it heats.

Feb 24, 2010 | 1993 Ford Ranger SuperCab

2 Answers

1991 Ford Ranger starts but stalla when in gear.


if it is an automatic the torque convertor could be locked up.

Aug 31, 2009 | 1991 Ford Ranger Supercab

1 Answer

O/D flashing 2000 Ford ranger xlt 4.0 4x4


ask if it has a tcc, or or maybe it's a tss
which is a torque convertor lockup switch
or torque c, sensor switch

Mar 31, 2009 | 1998 Ford Ranger SuperCab

3 Answers

Head bolt torque for a 1996 ford ranger 2.3liter


The torque specs and tightening sequence can be found in Haynes repair manual #36071.Ford Ranger 1993-2005

Jun 26, 2008 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...