Question about 1999 Jeep Grand Cherokee

1 Answer

Do not know how to take the spindle off from a 1998 jeep grand cherokee to reaplace the axel. I would prefer a phone call if you give me one. I have remove right down to the outer bearings but there is an alingment bolt that is holding the bearing housing in place. Does it have to come out or what. it is round. than you, Jay

Posted by on

  • mike loshbough
    mike loshbough May 11, 2010

    what is your phone #

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 2,039 Answers

If i remenber the bearing hold with 4 bolt but those bearing are a pain in the a$$ to remove if you remove that bearing the shaft should come off let me no thanks pierre

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a popping or crakin noise when i turn the wheel either way


center link for steering it bolts to the frame and the axle housing

Jul 23, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Jeep Grand Cherokee Laredo 1998 headlight assembly instructions


youtube.com type in 1998 grand cherokee headlight assembly, I just fixed mine in 10 minutes, both of them!

Mar 31, 2009 | 1998 Jeep Grand Cherokee

1 Answer

98 jeep grand cherokee won't disengage from 4x4


check the vaccume module on the front axel it my have come un pluged or the electric connector hope this helps

Mar 05, 2009 | 1993 Chevrolet S-10

3 Answers

Front axle replacement on jeep Grand cherokee 1998


""success! last night i just *had* to get at least one of them off so i
took a big hammer and a piece of wood and beat the sh*t out of the
driver's side spindle. it finally came off!
this morning i got to work on the passenger side one. no amount of
liquid wrench and beating would get it off. then i remembered the
"hot wrench". i took a propane torch and heated up the area behind
the spindle for a while. i didn't want to heat the spindle itself,
else it would make it MUCH harder (if not impossible) to remove.
after heating and beating it for a little while longer, it finally
gave!
thanks to all for the ideas-u guys rock! and so does the hot wrench...
smile.gif""

was here.

Jan 26, 2009 | 1999 Jeep Grand Cherokee

4 Answers

Rear end (axle)


call jeep and give them last 9 digits of your vin and ask for three things -Differential Type,Gear ratio, and Track lock- They will give you
1) Dana 35 or 44
2) Gear Ratio 3.31 or 3.73
3) Track Lock - yes/no

Jan 11, 2009 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...