Question about 2008 Subaru B9 Tribeca

Open Question

Loose outside foldin mirror on 09 tribeca

In locked position the mirror moves back and forth about a 1/4 inch how do you tighten this

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust linkage for transfer case


SHIFT LINKAGE ADJUSTMENT
(1) Shift transfer case into 4L position. (make sure your shifter is fully in the 4L position)
(2) Raise vehicle.
(3) Loosen lock bolt on adjusting trunnion (Fig.
87).
(4) Be sure linkage rod slides freely in trunnion.
Clean rod and apply spray lube if necessary.
(5) Verify that transfer case range lever is fully
engaged in 4L position. (you can do this under the vehicle at the transfer case)
(6) Tighten adjusting trunnion lock bolt.
(7) Lower vehicle

Basically, you are just ensuring that the position you put the lever inside the vehicle is the same position that the transfer case lever is in and then tightening the locking bolt.

Jan 27, 2016 | Cars & Trucks

1 Answer

How do I adjust the side view mirrors?


if it is not adjustable electrically from the dash, use your fingers on the inside or outside ,top or bottom or the mirror glass and gently re-position the glass position to suit your sitting position

Sep 13, 2015 | 2006 Subaru B9 Tribeca

1 Answer

Tighten side mirror


If the mirror housing is loose and nothing has hit it and broken the mounting to the door frame, yes. If it is the glass part that is loose and it is a electric or manual mirror, something has damaged it behind the glass replacing it will fix problem.

Dec 07, 2013 | 2007 Lincoln Mark LT

2 Answers

Where to add side mirrors on a 58 ford Fairlane


I've had the same quandary with my 59 Ford Custom 300 and the more of them I've looked at, the more I've noticed it seems to be personal preference. Mine are currently positioned just to the side of dead center on the top and directly across from the hood cowl side to side. I've seen some positioned on the fender just ahead of the doors or even on the doors to about a third of the way down the fender. I'm getting ready to move mine rearward, I like the look. It's all your vision, my friend. Good luck!

Nov 23, 2012 | Cars & Trucks

2 Answers

It starts to swerve to the left or right without turning the wheels almost like your swerving back and forth


sounds as though you have play in steering gear box- most of the time thier is a lock nut on top with a slotted screw in middle loosen lock nut and tighten screw then reset lock nut. do not over tighten slotted screw in fact tighten and then back off half turn so steering box is not too tight.

Jan 26, 2011 | 1981 Ford F 150

1 Answer

How do i replace the ignition switch in my 94 couger


Removal & Installation
  1. Disconnect the negative battery cable. Remove the upper steering column shroud by removing the self-tapping screws.
  2. Unfasten the four bolts retaining the lower steering column shroud, then remove the shroud.
  3. Remove the lock screw, and detach the ignition switch electrical connector.
  4. Rotate the ignition switch lock cylinder to the RUN position.
  5. Remove the two screws retaining the ignition switch, and disengage the ignition switch from the actuator.
To install:

NOTE A new replacement switch will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch run position.
  2. Check to make sure the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock approximately 90 degrees from the LOCK position.
  3. Install the ignition switch assembly into the column actuator hole. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  4. Install the retaining screws and tighten to 53–71 inch lbs. (6–8 Nm).
  5. Attach the electrical connector to the ignition switch. Tighten the lock screw to 7–11.5 inch lbs. (0.8–1.3 Nm).
  6. Connect the negative battery cable. Check the ignition switch for proper function, including the START and ACC positions. Also, make sure the column is in the LOCK position.
  7. Install the upper and lower steering column steering shrouds.

Feb 10, 2010 | 1994 Mercury Cougar

1 Answer

The glass in the driver side rear view mirror is loose. how do you tighten it up?


The driver and passenger side mirrors have a small rubber plug in the bottom center of the mirror housing. Remove the plug and there is a phillips head screw holding the mirror assembly. Tighten this screw about 1/8 turn and it will keep the mirror from moving around. If you remove the screw you can remove the mirror and drive motors. Use a bit of thread-lock to keep the screw from loosing again. Reinstall the rubber plug.

Jan 30, 2010 | 1991 Toyota Previa

1 Answer

99 explorer drivers side mirror vibrates


are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

  1. Remove the front door trim panel; refer to Section 501-05 .
  2. go to car-part.com for a used mirror. Page with * is cheapest seller.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
------------------------------------------------------
f9d70e9.gif
----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
4d9527f.gif

Apr 12, 2009 | 1999 Ford Explorer

1 Answer

Side mirror is coming loose from where the mount connects to the body. The top section is what is loose. Nothing hit this so I am not sure why its loose or how to tighten it. Thanks


You'll probably have to remove the sail panel (the triangular trim piece on the inside of the door which is positioned where the mirror base is). When you do that, you'll see that the mirror itself usually has studs that come through from the outside, and there are nuts on the inside that tighten down onto them to hold the mirror. Make sure that all the nuts are tight. If not, tighten them down.

What may have happened though, is that someone could've hit the mirror when you weren't around, and damaged something. It wouldn't always immediately sag or fall off, so it could've happened awhile back and you're just now seeing it.

Chances are though that the mounting nut/stud is the issue, and you'll be able to fix it this way.

Aug 10, 2008 | Toyota 4Runner Cars & Trucks

Not finding what you are looking for?
2008 Subaru B9 Tribeca Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...