Question about Cars & Trucks

Open Question

Were is the location of the inertis switch in a 1989 dodge dakota 4X4

Location of the inertia switch on a dodge dakota 4x4

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 60 Answers

SOURCE: steering come and goes.no fluid lost. no noise 2004 Dodge Dakota

the power steer pump is faulty

Posted on Aug 07, 2009

  • 5 Answers

SOURCE: 1988 Dodge Dakota brake line size question

they should be 3/16" but if you want to be sure, take a quarter inch wrench and put the open end over the line if it is sloppy on the line it is 3/16" , if it fits nicely, it is 1/4" . that is the only two sizes they could of used.

Posted on Jun 06, 2010

  • 2926 Answers

SOURCE: 92 dodge dakota 3.9 4x4 code 23,32 where is the


TESTING
This is a test of the sensor only. A complete test of the circuit requires the DRBII scan tool, or equivalent.
Unplug the wiring harness connector from the intake manifold temperature sensor.

  1. Using an input impedance volt-ohmmeter, measure across the terminals to test the resistance. The resistance should be less than 1340 ohms with the engine warm. Replace the sensor if not within specifications.
  2. Test the resistance of the wire harness. Do this between the engine controller wire harness connector terminal 21 and the connector terminal. Also check between terminal 4 to the sensor connector terminal. Repair the wire harness as necessary if the resistance is greater than 1 ohm.


ledsled378_9.jpg

code 32 is related to the EGR circuit. Remove the EGR valve from the intake and check for a clogged port(s). If ports are ok, replace the EGR. Check for vacuum leaks on all hoses and connections as well as the air intake tube. Sometimes the air intake tubes crack in between the ribs on on the ends where the clamps are, causing vacuum leaks.

Posted on Dec 04, 2010

pctech1
  • 1940 Answers

SOURCE: 2005 Dodge Dakota V8 4.7L,

  1. The Fuel Level Sending Unit, or Fuel Level Sensor, is located in your gas tank with the Fuel Pump Module. The fuel gauge sending unit (fuel level sensor) is attached to the side of the fuel pump module. The sending unit consists of a float, an arm, and a variable resistor track (card).
  2. The Fuel Pressure Regulator is located within fuel pump module. The fuel pressure regulator controls fuel system pressure. The PCM cannot detect a clogged fuel pump inlet filter, clogged in-line fuel filter, or a pinched fuel supply or return line. However, these could result in a rich or lean condition causing the PCM to store an oxygen sensor or fuel system diagnostic trouble code.
Both of these sensors are connected with the Fuel Pump Module. Here is a diagram:
pctech1_33.jpg

Posted on Mar 10, 2011

Ironfist109
  • 3018 Answers

SOURCE: re: 1993 Dodge Dakota, where might I find the fuel

  • You have an Automatic Shut Down Relay or "ASD Relay" not so much a "switch." The ASD relay inside the power distribution center which is under the hood on the left corner of the engine compartment. Under the lid is a legend that will pinpoint it's location in said box. I would look at this if your having problems with the fuel pump. Should you need to replace the pump the tank must be dropped for this vehicle.


11_7_2011_9_48_17_pm.gif


  • Hope this helps.

Posted on Nov 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheel hub assembly diagram


Go to you tube and ask for "How to replace Dodge Dakota front hub", you will find 2 or 3 good videos about it, I follow these videos and change mine in about 3 hours, note that I never did it in any car or truck. Another tip is that all videos I found was about 4x4 Dakotas and mine is 4x2, the only difference is the hub center fix, 28 mm screw on 4x2 and 32 mm nut on 4x4.

Apr 22, 2014 | 1989 Dodge Dakota 2WD

1 Answer

1987 dodge dakota 4x4 reverse lights do not work, wiring seems fine. Thinking a switch or relay prob. if so, where is it located. Help?


if it is a manual then it would be your reverse light switch, if it's auto then your neautal switch is worn seeing that you have check bulbs and wires already

Feb 16, 2014 | 1987 Dodge Dakota

1 Answer

How do you know when an air switching solenoid is bad on an 1989 dodge Dakota 4x4?


MIL (Malfunction indicator lamp) or check engine light illumination .You might see an Increase in tailpipe emissions or your Engine running rich, black smoke out tailpipe.

Dec 05, 2013 | Cars & Trucks

1 Answer

1995 dodge dakota 4x4 turns over but will not start, all relay switches are good, new rotor and distributer has been replace but the wire that goes to the fuel pump has no power, but fuel pump has been...


Most vehicles are equipped with what is called a fuel power inertia switch. It is a basic component that shuts down the fuel system during an accident to prevent fuel from being an factor during sensitive times. You may have to find and flip or replace this switch. I do not know the location of it on this particular model off hand, but if you consult your service manual you should be able to locate it quickly.

NOTE: on most vehicle it is located under the dash near the glove box. On some near the fuse box. On cars it is commonly in the trunk.

Thanks for using FixYa, if this solution does not work please feel free to come back and try again.

Sep 02, 2010 | 1995 Dodge Dakota

1 Answer

Where is oil filter located for a 1995 dodge dakota 4x4 v6


its around the engine mount L/S or R/S some have it on V6 left but you have a 4X4 and due to that is changees or there tuckd in higher. let me if this help.

Aug 01, 2010 | 1995 Dodge Dakota

1 Answer

93 or 94 Dakota Transmission


look at the starter bolting the location on bell housing differ depending where manufac...
plus start counting splines on the shafts..

May 07, 2009 | 1994 Dodge Dakota Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...