Question about 1994 Ford Ranger Supercab

Open Question

Where is the brain box located on a 1994 ford ranger 4.0 crew cab

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
losflip
  • 94 Answers

SOURCE: where is the power steering

The power steering pressure switch as its called threads in to the power steering pressure hose most of the time it is close to the power steering pump, I have also seen them at the lower point of the pressure hose close to the rack and pinion.

Posted on Nov 25, 2008

Ad
davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

  • 115 Answers

SOURCE: i NEED A FUSE BOX DIAGRAM FOR A FORD F150 2006

if your replacing a fuse... just ck all the fuses with a test light with ignition in on position...

Posted on Aug 01, 2009

  • 33 Answers

SOURCE: removal and install timing belt 1994 ford ranger/

Depends on the engine.

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers dont work, washer fluid does. not the motor, followed wiring to some sort of circuit board behind glove box


The Wiper Control Module is located behind the RH side of the instrument panel, near the top of tthe cowl panel.
michael_cass_315.jpg

Jul 14, 2011 | 1994 Ford F350 Crew Cab

1 Answer

Where are the brake line couplings located on the drivers side rear of a 1994 ford ranger 4wd extended cab?


the couplings are usually set in the frame before the gas tank or after the tank if its not one solid line from the master cylinder.the main one is sitting on the top or top side of the differential assembly and is easily seen.

Jul 06, 2011 | 1994 Ford Ranger Supercab

1 Answer

Location of flashers on a 2002 ford ranger?


Hello tonymccoy
The flasher relay is located in the aux. relay box behind the left instrument panel. In case they are
not marked, there are 4 small and 2 large relays, the large relay closest to the end of the box is the
flasher relay. Hope this is helpful.

Mar 08, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

Eec or ecu (Engine Computer) location on a 1993 ford ranger 2.3 ltr


This has a brain box located on left fenderwell, Its a small aluminum box about 6x6

Jun 15, 2010 | 1983 Ford Ranger

1 Answer

I have a 1994 4 cylynder automatic ford ranger. the truck will only start when it wants to, it could 15 minutes, or up to a month. I,ve replaced the main brain, the ignition module, 3 times, battery,...


My next thing to check would be the fuel pressure. It sounds like the fuel pump is not doing a good job to me. I say this thinking the system is getting fire.

Mar 27, 2010 | 1994 Ford Ranger Supercab

1 Answer

Scanner codes 335, 543 on 1994 ford ranger 2.3L 5spd manual w a/c. also where is the Powertrain contro module (PCM) located? NOT a supercab, regular


335 crank shaft sensor,543 (Mem) Fuel pump relay or battery power feed was open.PCM is located under the instrument panel, is the brain of the EEC system

Feb 06, 2010 | 1994 Ford Ranger Supercab

1 Answer

I cant find the cabin filter in my '03 superduty


Your cain filter is located under the windshield wipers. My brain cannot think of the name of the plate. But the black plate that the arms of the wipers are attached to needs to come off with torque screws and then once that panel is removed you will see a box saying cabin air filter

Apr 18, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Radio dose not work


According to your owners manual the Radio is Fuse #29 in he underhood Fuse/Power distreibution Box,

The power distribution box is
located in the engine compartment near the brake
master cylinder.

Feb 25, 2009 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
1994 Ford Ranger Supercab Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...