Question about 1999 Jeep Grand Cherokee

1 Answer

2003 Jeep Liberty Electric Mirrors only move a tiny bit then stop

Both left and right mirrors just started this at the same time. You can see the mirror move a tiny bit before it stops. Switch the L & R mirror switch back and forth and they again move a tiny bit and stop. Any Ideas?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

It sounds like the switch is going bad in the mirrro switch on the driver door should be able to get on at any dealer it should be any fix

Posted on Jan 25, 2009

  • Marc Podeszek Jan 27, 2009

    Please rate my response. Thank you !

  • Ben Geerdes May 22, 2013

    I have the same problem, was it the switch in your case?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Drive side mirror not working


Probably the switch I have seen many stop working and maybe one mirror stop out of hundreds

Apr 07, 2015 | 2003 Nissan 350Z

1 Answer

How do I replace power mirror switch, ford f250?


This mirror control switch will pop right out with just a thin blade type screw driver. Slide the blade of the screw driver under the edge of the switch carefully and twist slowly until you can see the switch coming up. You may need to re position the switch as there is a bit of play in the hole the switch fits into to. Once you have the switch up and out of the panel, carefully release the wires it is clipped to and replace it with one that is good. It is a typical sign these witches have gone bad if your mirror only moves in 2 directions or both mirrors are moving at the same time. I hope I have helped you with your problem.

Jan 22, 2013 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

My right mirror on 325 i 2005 doesn't work. When i change my seat position with the memory, the seats goes on but not the mirrors. I can adjust my left mirror but not the rigth one; it never move.


I would safely assume your right mirror may be inoperable period then by your statement you are leaving the switch for the mirrors in the middle during switching correct and during adjustment are switching to R/L mirror on the switch? Mirrors are on the same circuit so both should be operable. Have the mirror checked for operation before heading any further. I Think you will find during this its unplugged from its source of power or inoperable period and needs replaced. Remember to rate my solution and leave testimonial PS please purchase you a Owners Manual for your car you will thank me later.

Oct 09, 2012 | 2005 BMW 325i Automatic

1 Answer

I drove 1994 BMW 740IL and the passenger side mirror usually will move down when i put my car on reverse so i can see the curb view, however it stop working just now when i get in my car to back out from a...


Make sure your mirror control switch is slid to the right. If the switch is in the left mirror position, it keeps the right mirror in the upward position when in reverse. When the switch is in right mirror position, it moves the right mirror in the downward position when in reverse. Hope this helps.

Oct 23, 2010 | 1994 BMW 7 Series

1 Answer

Power mirrors dont stop adjusting to the right what would cause the problem?


this sounds like its the adjuster switch the one you use to move the mirrors left or right is stuck to the right, or stuck down on the right side of the switch, try replacing the switch this will possibly cure the problem...hope this helps

Sep 13, 2010 | 1991 Honda Accord

1 Answer

2008 Chev Suburban 4wd Z71 1/2 ton; several items on my passenger side stopped working: my passenger side front seat heater stopped working; the passenger side electric mirror stopped working; the signal...


Power windows an locks work ok ? Do you know anything about automotive electeronic control modules ?
Power Mirror System
Power Mirror System Components
The power mirror system consists of the following components:
• Driver Door Switch (DDS)--An electronic control module with integrated switches and requires programming when replaced
• Passenger Door Switch (PDS)--An electronic control module with integrated switches, requires programming when replaced
• Power Mirror Direction Switch--Integrated into DDS and is a 4 position momentary switch that provides a signal input to the DDS for up, down, left/extend and right/retract with a mirror switch activation
• Mirror Select Switch--Integrated into DDS and is a 3 position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• Left Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Right Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Body Control Module--An electronic control module that requires programming when replaced, serves as the power mode master and is the main message handler
• Memory Switch, if equipped with memory mirrors--Supplied power by the DDS and provides a voltage signal to the DDS upon a switch activation
• Horizontal and Vertical Position Sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDS/PDS and provide a variable voltage signal to the DDS/PDS that is proportional to mirror position
• Powertrain Control Module (PCM), if equipped with memory mirrors--An electronic control module that requires programming when replaced and provides the message indicating transmission gear selection
• Driver Information Center (DIC), if equipped with memory mirrors--Part of the instrument cluster which is a an electronic control module that requires programming when replaced and is used to personalize the memory recall functions
• Fold Motor, in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Each of the outside power mirrors contains 2 reversible motors to provide horizontal and vertical movement of the mirror glass. The vertical motor operates the up and down directions and the horizontal motor operates the left and right directions. If equipped with power folding mirrors, each outside power mirror will contain a reversible fold motor to operate the extend and retract functions. Each of the mirror motors are circuit breaker protected.

Do you know what DTC'S - diagnostic trouble codes are ?
DTC B1023
Circuit/System Description
The driver door switch (DDS) and front passenger door switch (PDS) each contain switches that control power door lock and window functions. The DDS also contains the control switch for the power outside rear view mirrors. These switches are integrated within the door control modules and are not serviceable as separate components. The DDS and PDS monitor these switch inputs for internal faults and set B1023 00 if any are detected.

You could have any number of problems an without testing , hooking up a scanner that can check DTC'S in the door module ,electrical circuit testing etc... we'd only be guessing . Your best bet mite be to take it to a qualified repair shop.

Feb 15, 2018 | 2008 Chevrolet Suburban

1 Answer

2003 gmc mirrors do not fold in


The power mirrors are controlled by a module (computer) DDM - drivers door module an the PDM - passenger door module .
Folding Mirror System
Folding Mirror System Controls
The folding mirror system requires signals from 2 separate switches. The mirror select switch must be in the neutral/fold position and the mirror direction switch must be activated to the left/extend or right/retract positions. Both switches are integrated into the DDM and provide direct signals.
Folding Mirror System Operation
Upon receipt of the required switch inputs the DDM will supply battery voltage and ground to the mirror fold motor control circuits to perform the requested extend or retract function. The DDM will also send a class 2 message to the PDM indicating the requested function. The PDM will supply battery voltage and ground to the mirror fold motor control circuits to perform the requested extend or retract function.

Power Mirror System
Power Mirror System Components
The power mirror system consists of the following components:
• The driver door module--Class 2 module with integrated switches and requires programming when replaced
• The passenger door module--Class 2 module with integrated switches, requires programming when replaced and also contains the RFA receiver
• The power mirror direction switch--Integrated into DDM and is a 4-position momentary switch that provides a signal input to the DDM for up, down, left/extend and right/retract with a mirror switch activation
• The mirror select switch--Integrated into DDM and is a 3-position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• The left outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The right outside power mirror--Contains both the vertical and horizontal mirror motors and is serviced as a complete mirror assembly
• The body control module--Class 2 module that requires programming when replaced, serves as the power mode master and is the main message handler
• The DDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The PDM 10A fuse--Located in the I/P fuse block and is hot at all times
• The memory switch, if equipped with memory mirrors--Supplied power by the DDM and provides a voltage signal to the DDM upon a switch activation
• The horizontal and vertical position sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDM/PDM and provide a variable voltage signal to the DDM/PDM that is proportional to mirror position
• The park neutral position switch, if equipped with memory mirrors--Provides transmission gear selection information to the PCM and is used for memory recall and mirror tilt in reverse functions
• The powertrain control module, if equipped with memory mirrors--Class 2 module that requires programming when replaced and provides Class 2 message indicating transmission gear selection
• The driver information center (DIC), if equipped with memory mirrors--Part of the instrument cluster which is a Class 2 module that requires programming when replaced and is used to personalize the memory recall and mirror tilt in reverse functions
• Fold motor in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Each of the outside power mirrors contains 2 reversible motors to provide horizontal and vertical movement of the mirror glass. The vertical motor operates the up and down directions and the horizontal motor operates the left and right directions. If equipped with power folding mirrors, each outside power mirror will contain a reversible fold motor to operate the extend and retract functions. Each of the mirror motors are circuit breaker protected.
DTC B1722
The driver door module (DDM) and passenger door module (PDM) switch the mirror fold motor control circuits to battery voltage and ground in response to mirror extend or retract command.

Apr 06, 2017 | 2003 GMC Yukon XL

2 Answers

Mirrors will not fold in.


It is a stuck motor. Water gives rust inside housing. Remove mirror and clean motor and components. This is a well known error for H2 mirrors.

Dec 18, 2008 | 2006 Hummer H2

1 Answer

Side view mirrors


the 4 buttons around that switch are the ones you press to move the mirror. to adj the drivers mirror, move the switch to the left, to adj the passenger mirror, move it to the right.

then you press one of the 4 buttons

Jul 21, 2008 | Hyundai Motor 2002 Sonata

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...