Question about Chevrolet 1500

1 Answer

My 94 full size blazer starts and idles fine in park and in neutral. When I put the truck in gear and hit the gas, it'll start, then act like it wants to die. The Catalytic converter is off, I'

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Yes try getting the fuel pump pressure tested by a mechanic. the other thing it can be is the injectors are plugged try running some lucas fuel system cleaner.

Posted on Jan 19, 2013

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 376 Answers

SOURCE: I have a 1996 Chevy

You might want to have a balance test done to make sure that your injectors are working properly.I worked on a blazer before and did the same thing by replacing everything not even giving thought to the fuel spider or the injectors.

Posted on Apr 14, 2011

  • 30 Answers

SOURCE: 94 s10 blazer dies when put into gear

Sounds like a vacuam leak, best thing to use is cold start spray, by spraying the vacuam lines with this you will notice a change in the idle wherever the leak is at.

Posted on Oct 14, 2009

  • 5252 Answers

SOURCE: moter ideles rough ,using lots of gas,dies when put into gear.

Earl! You could have bought a new car! Ah, but you must love this Ford truck, it's obvious from the never- say- die parts list. How long has this project been going on? If you plan on finishing it yourself. here's my thoughts: Invest in a good scan tool (about $150-$200), a good compression tester ($40), a vacuum gauge ($15), a multi-meter (your choice-a useful one starts as low as $20, a digital volt-ohmmeter (multi-meter) designed for auto electronics is desireable), and last, maybe a fuel pressure tester to round out the list (about $40). Maybe you have all or some of these already. They are all good diagnostic tools you will find very helpful in getting to the root of your problem. The place to start is with the scan tool. Look at trouble codes, look at live stream data. Both will help you a lot. Do a compression test. Find out the internal condition of the engine. New parts are good. Now make them work.

Posted on Jun 14, 2012

suarezelec20
  • 259 Answers

SOURCE: Erratic Idle - When starts the idle is about 1100 RPM as it warms up, it goes to 700 - 400 RPM

Have you "reset" the computer on the car. When parts are replaced, the comp continues to run the vehicle on all the old settings which can drive you nuts because nothing you do will fix a problem. Usually, taking both battery cables off and waiting for 15 minutes will reset the computer. If this does not do it, then ask a dealer how to reset yours.

Posted on Aug 31, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My car runs fine for days then i'll park somewhere and go to turn it back on and it won't start at all. It won't turn over or anything.


CHECK BATTERY CONNECTIONS, STARTER CONNECTIONS, WHAT DO YOU DO WHEN IT DOESN'T START, TO GET IT GOING AGAIN, DO YOU GET A JUMP START IF SO CHECK CONNECTIONS.

Jun 09, 2013 | Cars & Trucks

1 Answer

My 94 full size blazer starts and idles fine in park and in neutral. When I put the truck in gear and hit the gas, it'll start, then act like it wants to die. The Catalytic converter is off, I'm...


This could be a bad ground on the ECM. When it is in park it is open loop. When you put it in gear, the ecm goes closed loop with the oxygen sensors and with no ground it dies.

Jun 11, 2017 | Chevrolet 1500 Cars & Trucks

1 Answer

1996 monte carlo jerks when in gear but not in neutral


Have your modulator valve checked, or there could be a vacuum leak somewhere.

Feb 13, 2012 | 1996 Chevrolet Monte Carlo

1 Answer

2004 freelander hse erratic idle in park, fine in drive


Do you know what engine scan data is ? Disconnecting sensors is not the way to find a problem ! What is the computer seeing as data input signals . Is the vehicle in closed loop fuel control , is the EGR opening when it shouldn't be , Is the PCM controlling the idle air control valve or is the vehicle drive by wire (electronic throttle control ?
005 Idle Speed Problems Idle Air Control Test
007 Idle Speed Problems Scan Data for Idle

Jun 18, 2017 | Land Rover Freelander Cars & Trucks

1 Answer

1994 full size blazer runs fine for about a minute after start up after that it acts like it floods out catches back up everytime you hit the gas after 10 min of that it runs ok what is wrong with it?...


Sounds like it is either your tps or air idle control.
You dont say if you have a check engine lite on.
If lite is on it will be easy to find with a scanner.
This is a fairly common problem..
Hope I was of some help.......

Feb 09, 2010 | 1994 Chevrolet K1500

1 Answer

1990 full size blazer starts fine idles then dies


sounds real easy either a bad idle air control solenoid or more likley a blown throttle body gasket. to test fro a blown gasket, with engine running and cool spray carb cleaner or brake cleaner around base of tb were it bolts to intake. when it hits the bad area, should idle down and be normal for a second or 2. iac is possible,try this first since its so common and let me know

Aug 26, 2009 | 1990 Chevrolet S-10 Blazer

2 Answers

Vibration when in gear, and stalling.


The problem is the torque converter solenoid. I had it happen on my 94 Cavalier a few years back and was a cheap fix at the local car mechanic. What happens is the transmission warms up and hits a certain speed where the solenoid engages, but then it sticks and won't disengage until it cools down sufficiently. When it sticks, it causes the car to shake when slowing down and will snub out the engine if you come to a stop.

Mar 09, 2009 | 1994 Chevrolet Cavalier

1 Answer

Starts then dies when put in gear


does it do it only when engine is warm how the idle its going fine when its cold as soon you go over 70 km its start to do it let me know thanks pierre

Aug 17, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...