Question about Honda Civic

Open Question

1998 honda civic alignment specs - Civic Honda Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

short shadey
  • 421 Answers

SOURCE: 1998 honda civic ex sedan

remove rear seat, remove round metal cover, disconnect fuel lines and wires from top of fuel pump, jack up rear of car. remove gas tank straps, lower gas tank with a jack, install is reverse.....if you need to just replace the fuel pump you don't have to remove tank you Can access from under rear seat good luck and please rate -jeff

Posted on Sep 05, 2008

  • 1 Answer

SOURCE: Replacing head gasket on 1995 honda civic, require torque specs and secquence

wow. a lot of bad information on this site. Refer to a manual for the proper torque sequence. The civic I believe is a two step torque procedure. First 22 ft lbs, than 53 ft lbs.

Posted on Jan 01, 2009

johncaman
  • 201 Answers

SOURCE: reset keyless entry on 1998 honda civic

Okay, here goes-

1. Turn Key to on position.
2. Push and hold **valet button on the stock radio.
**Valet button is skinny bar located between am/fm & cd/tape buttons on stock radio.
Door locks will cycle one time.

3. Press any button on remote one time within 20 seconds. Door locks will cycle again.
4. To program up to 4 additional remotes repeat step 3 for each additonal remote.
5. Turn key off programming is complete.

Thanks for using Fixya, please rate if this helps :)

Posted on Mar 16, 2009

  • 21 Answers

SOURCE: 1998 honda civic parking brake frozen right rear wheel in cold we

do not use the park brake when it is cold--the linings are freezing to the rotor

Posted on May 21, 2009

  • 145 Answers

SOURCE: honda civic 1998 over heating. cooling fan problem? Where are the fuses for that. Thank you

Most likely you have a bad thermostat is stuck and not letting coolant to flow to your radiator. check your coolant level if is normal replace the thermostat NOTE: if you live air pockets on your cooling system then also cause to over head when adding new coolant open the bleeder valve if you cant find it just add coolant whit the engine running when the new thermostat open will release the air pocket and you will see a sudden drop of you coolant level, then add more on till the radiator is full again. never drive your car for long is your engine is over heating that will cause a blown head gasket and mayor repairs. if your on the street and just notice than your car is over heating turn your A/C off set it on heating maximum fan max heat and of coarse roll down all your windows. it be real hot for you but that will save your engine. the heater core on your car is like a baby radiator and bypass the engine thermostat that will help to cooled down a lot . hope this help you and good luck.

Posted on Jun 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need teardown and rebuild diagram for 1998 honda civic LX 5 speed manual transmission and specifications


Go to google and type in 1998 honda civic 5 speed transmission exploded view ,that should be helpful

Jul 21, 2012 | 1998 Honda Civic

1 Answer

What's the main & rod berring torque spec for a 96 honda civic vtec


http://ww2.justanswer.com/uploads/JHoop/2009-01-19_070643_torque_specs.pdf

Jun 13, 2012 | Honda Civic Cars & Trucks

1 Answer

Torque spec on head for 1986 civic si 1.5liter


Help need torque spec for cylinder head bolts 1986 honda civic dx 1.5 pls...

Mar 10, 2012 | 1986 Honda Civic

1 Answer

How do you relace a honda civic timing belt


It is really too much information to post here. You need to know how to align the timing marks, etc. Go to autozone and get one of the service manuals for you vehicle. It will be money well spent. If you want the factory service manual go to Helminc.com. They are pricey but excellent manuals.
Good luck.

Dec 18, 2010 | 1998 Honda Civic

1 Answer

1998 Civic: honda civic will not start...


good day Sir, try to check the battery and the fuse i hope it will help you.

May 16, 2010 | 1998 Honda Civic

1 Answer

Have a 00 four door civic lx need torques specs to put the 10 bolts back in


DOHC... 1st step =22 ft. lbs. 2nd step 61

SOHC... 1st step = 15 Step 2 = 36 #3 =49 fourth step only on bolts 1 and 2 = 49 ft. lbs

Sep 12, 2009 | 1998 Honda Civic

1 Answer

Tyre pressures for honda civic 1.4 1998


tire pressure is located on the door jamb at the drivers door on a white label or sometimes in the glove-box or in the trunk under the mat where the spare tire rests if the tires are of spec it is listed upon the tire itself near the rim you will see a series of numbers including tire size however 32-35 psi is almost always the correct pressure

Sep 09, 2009 | 1998 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...