Question about 1998 Chevrolet Malibu

1 Answer

Input speed sensor

Where is the input speed sensor on malibu 98 4 cl

Posted by on

  • dave smith
    dave smith May 11, 2010

    do you mean speedometer cable, usually these connect to your transmision, check underneath the car


×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,640 Answers

Near the joint on passengers side axle.

Posted on Aug 26, 2009

  • carl Feb 20, 2010

    it is near the joint on passenger side axle.

  • carl Jun 13, 2010

    tranny speed sensor is near the joint on passenger side of axle.

×

2 Suggested Answers

Molson02536
  • 3854 Answers

SOURCE: turbine input speed sensor

NO the sensor is out side the transmission. And it might just be a bad connection due to being out in the eliments. On the 3.1 your going to have to jack up the car to get to it from underneath and you should see it on the passenger side may be on top, Sorry been awhile and carful not to brake the clips that hold the wire to the sensor when disconnecting.
Good luck and hope this helps

Posted on Apr 09, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Malibu error codes po700,po716,po717


DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination

Which one of these transmissions does your Malibu have ?
Automatic Transmission - 4T45-E
Automatic Transmission - 6T40/6T45
Automatic Transmission - 6T70/6T75

Do you know how to find out look at the VIN # ?
DTC P0716: Input Speed Sensor Performance
DTC P0717: Input Speed Sensor Circuit Low Voltage
The automatic transmission input speed sensor (ISS) is a permanent magnet with a coil of wire wound around. The ISS mounts in the case cover facing the reluctor wheel of the input shaft. As the reluctor wheel is driven by the turbine shaft, an AC signal is induced in the input speed sensor. Higher vehicle speeds induce a higher frequency and voltage at the sensor. There is a fixed air gap between the sensor and the teeth on the sensor reluctor wheel. The ISS input is used by the transmission control module (TCM) in order to control line pressure, torque converter clutch (TCC) apply and release, and transmission shift patterns. This sensor is also used to calculate the appropriate gear ratios and TCC slippage. This diagnostic indicates stuck, erratic, or intermittent conditions in the system.
Diagnostic Aids
• Road test the vehicle while monitoring the Transmission ISS parameter on the scan tool. The Transmission ISS parameter should vary with engine speed changes and not abruptly drop out.
• Inspect for an open or shorted AT ISS wire.
• Inspect for a disconnected AT ISS connector.
• Inspect for a faulty AT ISS.

Trouble Code P0717 Input speed sensor

Jan 19, 2017 | Cars & Trucks

1 Answer

Where does the turbine input shaft speed sensor go on a 2010 cevy malibu Lt


Chances are that this sensor is located in the transmission or has access to it outside the housing.Take the car to a transmission specialist and have them give you an estimate.Most dealerships these days don't even do trany work anymore so save yourself some money and go directly to someone who can help you.good luck

May 22, 2014 | 2010 Chevrolet Malibu

1 Answer

97 Acura CL D4 light flashing


You change the transmission control molcule (TCM).

Jul 26, 2013 | 1997 Acura CL

1 Answer

98 Buick Park Avenue (Turbo) P0717 fault code,


CODE PO717 IS - A/T INPUT SHAFT SPEED SENSOR LOW INPUT CONDITIONS.YOUR INPUT SHAFT SPEED SENSOR COULD BE DEFECTIVE.CHANGE FLUID + FILTER IF IT HAVE NOT BEEN CHANGED IN A LONG PERIOD OF TIME.

May 29, 2010 | 1998 Buick Park Avenue

1 Answer

Where is the input speed sensor located


There is no input speed sensor on a malibu. Only the out put. the out put speed sensor is located on top of the trans close to the pass front tire. Follow the axel into the trans on the pass. side and then go up. . You will see a wire connector on it.

Hope that helps

Aug 28, 2009 | 2002 Chevrolet Malibu

1 Answer

Turbine input speed sensor


NO the sensor is out side the transmission. And it might just be a bad connection due to being out in the eliments. On the 3.1 your going to have to jack up the car to get to it from underneath and you should see it on the passenger side may be on top, Sorry been awhile and carful not to brake the clips that hold the wire to the sensor when disconnecting.
Good luck and hope this helps

Apr 08, 2009 | 2000 Chevrolet Malibu

1 Answer

Speed sensor


it has an input and an output spped sensor located on the front side of the transaxle

Nov 20, 2008 | 1997 Chrysler Sebring

Not finding what you are looking for?
1998 Chevrolet Malibu Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

67911 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...