Question about 1998 Nissan Quest

Open Question

Replace 1998 nissan quest positive battery cable

Replace positive battery cable

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4369 Answers

SOURCE: 1999 nissan quest brake pad replacement

Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Posted on Jan 21, 2009

Ad
  • 30 Answers

SOURCE: replace control panel on 2004 nissan quest

there is a c-clip you need a small screwdriver to pull it out then gearshift knob will pull off

Posted on Jan 28, 2009

  • 840 Answers

SOURCE: replacing belts after replacing water pump on 1996 nissan quest x

the easist way is to loosen the alternator slide the alternator down then slide the belt where it should go then pull up on the alternator again and bolt up Please rate my response thank you very much

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: Battery drains in my 2004 Nissan Quest

I have the same problem on my 2004 Nissan quest, and the battery will die if i do not drive it for 3-4 days, i have replace a ACdelco ACD24F60 new battery and it has the same problem too. I just get a Nascar advantage charger Model 11-1577-6 from Canadian tire, and try to recharge it but the LED flash after few hour, I set to normal battery type, any idea how to fix this problem. thanks.

Posted on Feb 14, 2010

johnjohn2
  • 5763 Answers

SOURCE: 1997 nissan quest camshaft sensor where is it & how to replace it

The camshaft sensor is located inside the distributor and is part of it, in order to replace it you must replace the distributor,to replace remove the dist cap. mark the location of the rotor,by marking where its pointing to, then mark the dist housing, so now theres a mark on the rotor and housing to show where rotor points, next mark the location of dist going into housing, mark the shaft and the block,because it spins in block this way you can line back up.next remove hold down bolt and pull out,mark the new dist in exacat same spots as the old so you can install back the same,you may have to put it in and pull it out until your marks are lined up,this way the timing will be dead on, when done you can check timing. good luck

Posted on May 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1998 nissan quest dies when put into gear


Fix any visible fault and then try

Nov 02, 2016 | 1998 Nissan Quest

1 Answer

I have a 1998 nissan quest and has charging problem i replaced the battery and the alternator


I would take it to autozone or kragen one of them should have a machine they can wheel out to the van and test the charging system for free.It will check starter,alternator,battery,the whole system.

Dec 30, 2012 | 1998 Nissan Quest

1 Answer

How to replace battery


Open the hood of your car and locate the battery.
Disconnect the cable terminals from the old battery's terminals (negative/black first and then positive/red)
Connect the cables to the new battery securely - positive to positive and then negative to negative. The cable ends should not be able to move at all; any looseness can prevent your car from starting.

Sep 21, 2012 | 2005 Nissan Quest 3.5 S

1 Answer

Need to replace speed sensor on a 1998 nissan quest mini van


the sensor is located on the trans housing above the right axel where it inters the trans

Jul 25, 2012 | 1998 Nissan Quest

1 Answer

I have 2007 nissan quest. I replaced the battery and now the van only cranks and cranks but won't start. Also the alarm doesn't respond or the automatic doors don't function either. Someone...


If you follow the positive cable (right at the post in most cases) there is a 50 amp fuse. You may have blown that fuse whicgh is common when changing the battery unless you remove it. Connecting the positive cable first when installing the battery helps prevent this. Also there are several other fuses that you may have blown which connect to the theft system going to the body control module which will prevent the vehicle from stating. If the fuse on the posive cable isn't blown (which I bet it is) in the fuse panel in the vehicle check fuse number 3, 4 , & 19 . See layout diagram below. Also in the fuse panel in the engine comapartment you can check fuse number J and 25 . See layout diagram below. I hope this helps and good luck.


clifford224_529.jpg

clifford224_530.jpg

clifford224_531.jpg

Sep 22, 2011 | 2007 Nissan Quest 3.5 Minivan

1 Answer

Need a manual to change the starter on a, 1994 Nissan, Quest mini van + 6 cylinders


http://groups.yahoo.com/group/villagerquest/

Section 03-06: Starting System 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

Apr 27, 2010 | 1994 Nissan Quest

1 Answer

What is the negative battery cable bolted to and do I have to remove the battery to replace the cable?


The negative terminal on the battery is the one with the minus, usually the positive is red.
Disconnect the negative cable from the battery for safety. Then follow the cable to where it attaches to either the engine block or the body. They unbolt it and replace it.
You shouldn't have to remove the battery for this. Just don't mess with the positive terminal. You will have to reset the radio stations etc since battery is disconnected.
If the connection at the negative side is corroded, just cut it and reconnect it with a new battery terminal. A parts store can hook you up with that.

Nov 07, 2009 | 2000 Nissan Quest

1 Answer

My 95 nissan quest


2 hour job from top driver side of engine.

Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

May 27, 2009 | 1994 Nissan Quest

1 Answer

I have 1998 Nissan quest, the power dies when I turn the key to on(ignition) position. I checked the battery still ok. pls. help


does it do it all the time or when you first start it after it sat for a period of time, if sat a long time something is draining your battery, comething with the charging system or a bad relay that does not shut off

Feb 26, 2009 | 1998 Nissan Quest

Not finding what you are looking for?
1998 Nissan Quest Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...