Question about 2000 Volkswagen Jetta TDI

Open Question

Looking for fuse for abs on 2000 jetta not working.fuse side drivers door good

Abs lite on and no abs .brake lite on to.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Murphybanton
  • 2004 Answers

SOURCE: passenger seat heater not working in my 2003 volkswagen jetta

There are different fuses. check your fuses properly.

rate this fixya

Posted on Mar 24, 2009

Ad
CMV9
  • 594 Answers

SOURCE: door panel

here is a diagram of how to unistall your door panel. please do not forget to rate and comment about your experience with fixya today.

Driver's Side Door
NOTE This procedure is for models with power windows. If equipped with manual windows, refer to the procedure for the Passenger Side Door Panel.


NOTE Do not grasp in grip depression when pulling off grip recess, as there is a strut secured to door trim underneath.

  1. If necessary, make sure you have the radio code.
  2. Make sure the ignition if OFF, then disconnect the negative battery cable.
  3. Insert a suitable prytool in lower partition between the panel and grip recess.
    42075_vwca_g0157.gif Insert a suitable prytool in lower partition between the panel (1) and grip recess (2)
  4. Unclip the grip recess upward out of door trim. Do NOT reach into grip depression while doing so, to prevent damage to brace.
  5. Press the locking lug against the connector (3 – arrow) and pull it off.
    42075_vwca_g0158.gif Unclip the grip recess (2) upward out of door trim. Do NOT reach into grip depression while doing so, to prevent damage to brace (1). Then , press the locking lug against the connector (3 – arrow) and pull it off
  6. Unscrew the 7 mounting bolts.
  7. Unclip the door trim at the sides using disassembly pliers 3392, or equivalent.
  8. Lift the door trim up out of window recess.
    42075_vwca_g0159.gif Unfasten the 7 bolts (arrows). Use pliers to unclip the door trim (1) at the sides, then lift the trim up out of the window recess
  9. Unclip the cable guide using a prytool, pull out the bracket in the direction of the arrow, then unhook the cable hook.
    42075_vwca_g0160.gif Unclip the cable guide (1) using a prytool (2), pull out the bracket (3) in the direction of the arrow, then unhook the cable hook (4)
  10. Disconnect the connectors and remove the trim panel from the vehicle.
    42075_vwca_g0162.gif View of the driver’s side door panel—with power windows
To install:
  1. Pull off the window recess seal from door trim and insert in window recess.
    42075_vwca_g0161.gif Pull off the window recess seal (1) from door trim and insert in window recess
  2. The remainder of installation is the reverse of the removal procedure, noting the following:
    • Before installing door trim, check all clips and replace as necessary, and insert into mounts of door trim.
    • After connecting battery, check that the vehicle equipment (radio, clock, electric windows) is operating properly.
    • If the Electronic Control Module (ECM) is subject to low voltage with ignition on, DTC memory and Readiness code must be checked with a scan tool.

Posted on Apr 16, 2009

  • 86 Answers

SOURCE: how do i remove drivers side door panel that has

theres a clip behind the crank handle pop it with a screwdriver and pull handle.

Posted on Jul 22, 2009

  • 119 Answers

SOURCE: 1999 passat v-6 abs,brake lite come on,oil lite

A friend of mine has a VW Sharan V6 that done almost the same things and it was the electric water pump on the front bottom right of the engine that seezed up( yours is most likely doing the same), it's a black cylindrical sausage shape but a little thicker in size.The water leeks into the motor when it seezes and causes a intermittent short circut.

Posted on Feb 02, 2010

roniecon
  • 6826 Answers

SOURCE: brake lights are out both sides only center works.

Check the brake light switch,and look for a brake light relay.

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1997 Jetta all brake lights quit working. Fuses are good bulbs look good and brake light switch looks ok could a bulb be bad and cause all three to go out?


I'd want to check voltage and ground for the stop lamps. Use a test light.
In the diagram for brake switch, the top wire is voltage, hot all the time, use a test lite to check for voltage, that circuit is fuse protected.
The lower wire in the picture goes hot when brake switch is activated and carries voltage to lamps. Like I said, the lamps need voltage and ground.
26342054-uv0rfzpbx2a3p0tlbleps30a-3-0.jpg

Nov 05, 2016 | Cars & Trucks

1 Answer

Abs light on in 2000 Alero 3.4


check fuses..If the fuse blows the light comes on and the ABS system is not working..Or possible the abs motor is shot. In any rate it is a good idea to look into it as soon as possible. You ABS system is not working. You still have brakes but the anti lock system that prevents skids will not work

Feb 12, 2015 | 2000 Oldsmobile Alero

1 Answer

2003 jetta. EPC lite is on. brake lites do not work. cruise does not work.


Check all your ground points. The brake lights and cruise may be grounded to the same spot. Re-check the cruise fuse and brake/tail light fuses.

Oct 13, 2012 | 2003 Volkswagen Volkswagen Jetta

1 Answer

Passenger door window switch


https://s14.postimg.org/6r7zxgtox/power_windows.jpg

Click on the link.
I can only help by telling you to check voltage and ground circuits. You check voltage by using a test lite, see the fuse in diagram, not only check the fuse, check the fuse circuit for voltage.
To check ground, you can still use the test lite, one end comes from voltage, the other end you touch to ground wire, the actual wire not the insulation, if the lite comes on, at least you know the ground is good enough to turn on the lite.
You can see voltage wire color coming from fuse. The ground wire not in the picture, black with yellow tracer.
on the hinge side of driver door is usually a wiring harness going into the driver door, probably has a protective covering, move cover back far enough to find the wire colors you want to check.
You open/shut driver door so much, sometimes those wires may break?

Apr 16, 2017 | 2006 Mazda 6

2 Answers

My tail lights are not working on my 2000 jetta the front lights work the break lights work and the blinkers work all inside lights work just fine


you need new bulbs in tail lights one bulb in each side has two elements one works brake other works running lights the elements in the bulb for tail lites are bad . so just replace bulbs. hope this helps.

Sep 13, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

I have a 2000 GMC Sierra. Brake Light and ABS warning light comes on frequently. Sometimes it's there othertimes not. Have replaced the sensors, replaced rotors and pads, cleaned gound on the frame...


I would recommend checking for diagnostic trouble codes in the ABS system. If there is a diagnostic code C0265 set, then you're most likely looking at an ABS computer replacement. This is a common failure on these trucks. GM calls this computer an EBCM, or Electronic Brake Control Module. This is the controller for antilock brakes and is mounted directly to the ABS pump motor assembly. Last time i checked, these things were going for about $900 at the dealer.

Aug 08, 2011 | 2000 GMC New Sierra 1500

1 Answer

Looking for the fuse box for lights on a VW Jetta


all the fuses on an mk3 vw such as yours, are under the dash on the drivers side. they are kind of a pain to get to, but if you look under the steering wheel, above the gas and brake pedals, there is a little door that opens, the door has a diagram showing which fuses are which. usually the fuses dont go though, have you checked the bulbs?

Jul 25, 2009 | 1995 Volkswagen Jetta

1 Answer

ABS Light and Parking brake light on


check your fuses, then check the ABS valve located beside the master cylinder and the wiring to it and finally check your speed sensor, which is located on the transmission on a 2 wheel drive and on the transfer case on a 4 wheel drive. but make sure hat your E-brake is released as it will cause these lites to come on.

Oct 09, 2008 | 2000 Chevrolet S-10

1 Answer

Anti lock brake system


Good Day,

That's usually caused by a bad abs sensor and/or wheel bearing. The quick fix is to locate the fuse box, on that it should be on left side of the dash, only accesable with the driver's door open. Locate the fuse for ABS and remove it, ABS is now disabled, this will trip the ABS light on the dash, also keep in mind you will lock your brakes under heavy braking conditions.


Hope this helps

Jul 05, 2008 | 1994 Oldsmobile Bravada

Not finding what you are looking for?
2000 Volkswagen Jetta TDI Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...