Question about 1999 Jeep Cherokee

Open Question

How to replace a window washer pump on a 2000 jeep cherokee

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
whispers76
  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

Ad
picatudo
  • 239 Answers

SOURCE: 1999 windshield washer pump relay

there is no relay is the same fuse for the wipers

Posted on Jan 14, 2009

  • 2 Answers

SOURCE: How to replace headlights on 2000 Jeep Grand Cherokee

One long bolt at the top - requires a 7mm socket to remove the bolt. The light housing will pry out with a screw driver. There are three ball and socket type connectors that hold the housing in and I just pryed off the plastic housing carefully and "balls" pop out of the sockets. Finally, I was replacing the faded plastic housing and it came with a new wiring harness. It's impossible to reach the connector to use the new wiring harness that comes with the new plastic light housing. So just use the existing wiring harness with the new light assembly.

Posted on Feb 06, 2009

  • 4 Answers

SOURCE: 2000 jeep cherokee sport fuse diagram

unfortinately the fuse box is under the hood and there is no panel inside the 2000 cherokee or diagram, i had to buy an online manual to find out what fuse went where for my jeep but its not with me. You can just pull the fuses out one at a time and look at them - I know its a pain. It might be your window controll switch - mine is bad as well. It is a common problem for these cherokees especially over 100k, they wear out - I initally thought it was my fuse as well because the lights in the window switch didn't light up anymore - but it is my switch.

Posted on Feb 15, 2009

  • 29 Answers

SOURCE: 1999 Jeep Cherokee rear window washer

There are two separate washer pumps underneith the washer res. behind the front driver quarter panel. The exact pumps are hard to find. I have the same prob with my 99, but both are out. I had a 98 that the front worked but not rear. I had to get a "universal" washer pump. I'm still trying to find a factory replacement for this one before I do that. No luck so far.

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Jeep Cherokee Sport that I beleive needs the washer fluid pump replaced and am seeking advice on where it is located and how to replace it.


the washer pump is located in the bottom of the washer bottle.if you remove the bottle disconnect the washer hose and electrical plug.most of the pumps you just pull it out of the rubber o ring that seals the pump so the fluid won`t run out and holds the pump in place.

Oct 25, 2011 | 2000 Jeep Cherokee

2 Answers

Hi...I have a 1999 Jeep cherokee Sport. The windshield washer quit..dont know if it is a clogged line or a pump. Not hearing the pump when I activate. Also lines appear to be hidden.


This is most likely due to the washer pump going out. I just replaced mine on my 2000 cherokee. There is a front and back pump which is located under the drivers side fender. You will have to remove the plastic corner bumper to get access to the pumps. This is an easy job to do yourself. Dont forget to have something ready to drain the fluid into when you remove the pump from the washer tank. The front pump is located below the rear pump.

Dec 01, 2010 | 1999 Jeep Cherokee

1 Answer

Replace a washer pump for 2000 jeep cherokee 6 cyl.


Visit the autozone.com website and register the vehicle. It doesn't cost anything and you will have access to an online repair manual for the vehicle. The steps for replacing the water pump should be available there. Hope this helped and best wishes.

Sep 07, 2009 | 2000 Jeep Cherokee

1 Answer

Where is the washer pump in a Grand Cherokee Laredo 2000


It is located in the bottom of washer reservoir (bottle).

Jul 01, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 jeep grand cherokee 4.0 liter engine timing belt replacement


If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Apr 04, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Replacing water pump on 2000 Jeep Grand Cherokee V6


i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Jan 10, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 Jeep Cherokee Windshield Washer


You have a motor for the front and rear washer. Check the fuses. If the intermitted wipers does not work, there is a relay under the dash near the steering colum that needs to be replaced.

Jan 01, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 Jeep Cherokee Sport, window washing does not work


the little pump inside the washer fluid reservoir is bad, replace it

Dec 27, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...