Question about 1998 Jeep Grand Cherokee

1 Answer

Intermittent High Speed Wobble around 50 mph

The vehicle does not do this everytime around 50mph. Sometimes it is minimal, other times I must come to a complete stop to stop the vehicle from shuttering. May do it while coming up to a speed or slowing, but around 45-50mph. I have tried different tires on the front, and replaced the track bar. Still does not help.

Posted by on

  • b_ser04 Jan 25, 2009

    I checked the ball joints, tie rod ends and sway bar and everything is tight. Any other suggestions?

  • Stacy Gilfilen Jun 09, 2013

    Did you ever find out what was wrong? I have a 2007 jeep commander that does the exact same thing.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,674 Answers

Have an alignment place check your idler arms & steering links, and tie rods for play, as well as the rest of the front end. that's a dangerous thing to fool around with.

Posted on Jan 25, 2009

  • Mike Butler
    Mike Butler Jan 27, 2009

    This is 4 wheel drive, or 2 wheel drive?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loud ticking noise on driver side as speed hits 50mph gets louder as mph goes higher but noise gets quieter when mph goes down. If I do not reach 30-45 mph it will not tick, what is causing it


Noises are decieving. Cud be steering system or wheels or suspension. If ball joint fails car cud flip ovr.hav pro testdrive it. Seek a gudguy at surecritic.com

May 21, 2015 | Cars & Trucks

2 Answers

On 98 caravan 2.4 it starts to wobble at 40up to 50 mph mostly when accelerating when speed reached smoths also smooths out after 50 mph alll new including valves. could bad wires cause this?


How old are the good tires? These speeds usually mean belt or balance problem with tires...If new tires, they need to be re-checked for balance...and not out of round...also check for bent wheel...due to chuckhole? Sometimes a bent steel wheel can be hammered straight...hope this helps.

May 08, 2015 | 1998 Dodge Caravan

1 Answer

What causes slight vibration?


sounds too much like a wheel imbalance, check all the wheel nuts are tight too (I know it sounds stupid but it has happened to me) some off-road tyres have a speed limit set to around 50mph.

May 07, 2014 | 2000 Jeep Grand Cherokee Laredo

1 Answer

Transmission trouble?


is rpm at 4 means rpm at 4000. if so assuming everything is okey in the transmission. check your Vehicle Speed Sensor it looks like your not getting the signal which tells you computer to shift at overdrive when speed is over 50mph.

Nov 06, 2013 | 2002 Dodge Intrepid

1 Answer

My olds88 skips at speed around 50 mph. it runs good under 50mph


Replace plugs and wires at the same time. Check for vacuum leaks

Mar 18, 2011 | 1997 Oldsmobile 88

2 Answers

2004 Chevy Trailbalzer LT front end wobbles at 55-65 MPH. It will sometimes smooth out at 70 but is intermittent from time to time


Do this first.. drive this vehicle very slowly on a smooth straigh road. If the wobble is noticed you have a broken steel belt in your tire that fluxuates at different speeds causing this to happen

Dec 26, 2010 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

3 Answers

2001 jeepgrand cherokee wobbles and shakes @low speed


could be a bd axle or ball joints wheel bearings are also a concideration

Aug 02, 2009 | 2001 Jeep Grand Cherokee

2 Answers

Van seems to wobble when the speed gets brtween 35 and 50 mph


Have your van checked for alignment, camber and have those front tires balanced.

Nov 29, 2008 | 1993 Plymouth Voyager

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...