Question about GMC Sierra

Open Question

Power seat won't tilt gmc pickup

Driver side seat bottom will not move up or down, it will side and back reclines ok

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: driver side car seat

The seat may be too far forward, and when it is at the forward limits, the seat sticks. I get in the seat, and I press the back button whilst pushing hard with my feet against the floor.

Posted on Nov 04, 2008

Ad
FIXYA Benny
  • 165 Answers

SOURCE: Power seat won't recline

are there any other leavers or dials around the seat that you can see that may operate the back rest independantly?
can you see the motors are they intact?
is there a button that selecets the particular funtion you wish to do?
it is functional, can you test that?
dirt is a major key in faulty switcches and can oftem be cleaned

Posted on May 05, 2009

  • 1 Answer

SOURCE: 2000 Park ave - power seat problem

The electric adjustment motor has a drive-gear that engages a gear on the shaft of the adjustment screw (90 degree engagement). The gear on the adjustment shaft looses a tooth. Adjustment motor whines, drive gear on adjustment motor spins, no action though because of missing tooth. A 12mm 1/4" drive socket on a wiggler (universal) on the end of a 6" extension can engage the not on the end of the exposed large adjustment shaft and, as the shaft is lightly loaded and the electrical switch engaged, one can get the shaft to spin almost one revolution at a time until the seat is high enough. It is hard to reach the nut necessary (inside the dull-grey clevis that the shaft threads into) and I had to take off the seat pad by removing the 4@ 13mm nuts (and 3 @10mm nuts holding the center section with the driver's cushion) to more-or-less easily access the situation. Dealership wanted well over $1000. to fix it. Three out of my 4 up and down adjustment motors are running, but don't adjust. PS, on my 2001 Park Avenue on each seat there is one adjustment motor for the front edge up and down, one adjustment motor for the rear edge up and down, one adjustment motor for the seat fore and aft, and one adjustment motor for the sear back tilt. Lots of complication, not so much on durability. We do not swap out drivers and adjust the seats excessively. Weak design on the one internal gear. Manually adjust it, unplug the electric to the motor, Drive happy again.

Posted on Aug 13, 2010

  • 2 Answers

SOURCE: 2004 Pacifica power seat don't work

I have the exact same problem and I am wondering if you've found the source of the problem??

Posted on Sep 04, 2010

  • 104 Answers

SOURCE: Front drivers seat won't recline and its stuck

electric or manual?

Posted on May 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Back tilt is a manual round knob on drivers seat it just turns


It sounds like the inside of the recliner knob is stripped out. If you go to your local GM dealership and give them your VIN number they can order you a new one. Here is the removal and installation directions.
Driver or Passenger Seat Recliner Handle Replacement Removal Procedure
  1. Use a flat-bladed tool to remove the plastic center cap from the center of the recliner handle.

  2. Pull the recliner handle off the shaft.
Installation Procedure
  1. Install the recliner handle on the recliner shaft.

  2. Push the recliner handle firmly onto the recliner shaft until fully seated.
  3. Install the plastic center cap into the center of the recliner handle.
Hope this helped please hit the accept button and positive feedback is appreciated.

Jul 16, 2013 | Oldsmobile Silhouette Cars & Trucks

1 Answer

HONDA ACCORD Seats Front Assembly Recliner went down and won't go up


I wouldn't ruin anything by trying things yourself

I would have a dealer check it out

The dealer I used in the past, has a seat specialist come
in on Wed only, around 5:30 after the service bays close
& one service writer hangs out until that person fixes a
couple vehicles seat issues

Jun 12, 2012 | 1995 Honda Accord

1 Answer

2005 Nissan Altima - seat would do everything except recline. Hit the forward side and it has gone all the way forward (recline switch). Now, of course, the seat is not in a drivable position and...


If it will move in every other direction I would start by looking under the seat and check down in the seat trac for something lodged in it way.

Dec 12, 2017 | 2001 Nissan Altima

1 Answer

1997 olds silhouette drivers side power seat won't move. Stopped full back. No fwd back, up, down or tilt. No noise from any motors.


either the seat motors out or the seat relays bad check to see if you have power to your motors if so then the motor is defective if not then find the relays and fuse

May 11, 2011 | Oldsmobile Silhouette Cars & Trucks

2 Answers

My front seat will not move forward. It will recline, move up and down but it will not move forward. I've tried reseting the seat positions but nothing seems to work. my seat wont move forward is there a...


You can move the drivers seat back by turning on the power, getting in the seat and position your feet firmly on the fron flor with your back firmly against he seatback, and then engage the switch pushing back - while pushing like hell with your feet. You can actually hear the seat drive shaft turning while the seat moves back. The principle should be the same for moving forward, but pressure would have to be aplide to the back of the seat.

Jun 02, 2009 | 2004 GMC Envoy

1 Answer

Power seat on drivers side of 1996 buick park ave. wont go in reverse every ting else works ok


Chances are one of the motors has gone out. There are 3 motors for each of your power seats. One controls the forward/backward motion, one controls up/down/tilt, and the third controls the reclining seat back. In my '95 model, there is one fuse for the seats under the driver's side dashboard. There should be a diagram inside the fuse panel cover denoting which one controls the seats. Hope that helps!

Apr 26, 2009 | 1996 Buick Park Avenue

2 Answers

2000 blazer power seat


The guy that posted the first solution...that works...My power seat module went bad , so I used a 12 volt batery charger on the wires to move my power seats.

Mar 19, 2009 | 2000 Chevrolet Blazer

1 Answer

2000 GMC Jimmy Power seat stopped working


both my power seats are not working at all ..it first started with driver seat , to make seat move forward and back tilting the recliner was working then it went out ..not working either..then after a month later my pasenger seat stopped working as well... what might be the issue..please reply

Jan 23, 2009 | 2000 GMC Jimmy

3 Answers

Power front seats


Use a hammer and tap each of the travel rails on seat, this worked great for me, something just gets misaligned in there.

Nov 09, 2008 | 2002 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...