Question about Cars & Trucks

1 Answer

My truck is macking a scicking nose it's not the brack pads I just check that does any body no what it might be pleas help thanks.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,103 Answers

Look at the driveshafts and the joints in those..if the sound is repitishious(repeats itself )as the vehicle speeds up slowly from a walking speed to a slow roll ,, it will almost sound like a chirping bird.in bad cases it will make a hard thunk sound gong from drive to reverse..there are 2 shafts one at the front and one at the rear.usually the front one fails first because its the smaller of the two..good luck and repost findings please..if its a metallic screeching check the brakes for wear(gm uses a small fingr on the pad to warn of worn pads and it may be to that point..just to be sure..

Posted on Jan 19, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: asb light and brack keep flash and i have had pads changs

im pretty sure its your fluid level (steering) screw top as you stand infront of car right hand side screw top with metal connector attached

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 toyota tundra v8 and when i put the truck in reverse and drive it, it squeeks. but if i wet the back axel and the back of the brakes it eventually goes away for a couple of days and comes...


hi,if it has drum bracks it could be brack dust inside the drum,if its disk bracks they might need copper- slick put on the brack pades,on the side that faces the brack-caliper.
hope this was some help.

Oct 29, 2013 | Toyota Cars & Trucks

2 Answers

My Chevy surburbon 03 1500 is macking a nose coming from the front left wheel


check for a loose wheel..take the wheel and shake it(while jacked up off the ground) rotate it and look behind it for any loose hardware bad bearings or anything you can see that makes noise or dont look right..repost with findings,, thnx

Jan 19, 2013 | Cars & Trucks

1 Answer

While I am driving when I am pressing the gas pedal it makes a scraping noise but not all the time. If I hit the brakes it will stop. I have a 2001 Nissan Sentra GXE


Sounds like it might be the low brake pad indicator. A small flap of metal which is made to scrape the rotor when the brake pads reach a certain low level. When brackes are applied the noise typically quiets.
Check for worn front brake pads.

Jun 26, 2011 | 2001 Nissan Sentra

2 Answers

Grinding noise from rear and rear brack hub hot


Collapsed rear wheel bearing or worn brake shoes or pads. You will need to pull the wheel and hug off to check both.

Jan 16, 2011 | 2002 Kia Rio

2 Answers

Our car has been sitting parked for the past 8 months, today we tried to move it and the back brakes are locked, and the back wheels will not move? What could be the cause of this?


The bracke drum / Hand brake cable is stuck . Try to hammer the rear wheel centre and if the brake drum is stuck it wiill be released .
Also the cable of hand brake is stuck . try puling the hand lever of the hand brake up and down many times this may free it .

Mar 14, 2010 | 2000 Hyundai Elantra

1 Answer

How do you get the rear brake calipers to retract in order to fit new pads?


use a c clamp to push the caliper piston back in, after its in replace the pads ,all back to gether, push the brack pedal till it feels good, hope this helps you, robert b.

Jun 06, 2009 | Chevrolet Cobalt Cars & Trucks

1 Answer

Brack pad change on 2003 volvo s40


It is the same as the older cars.
Just change the pads as usual.
It`s when you come to bleed the brakes that problems arise.

Feb 02, 2009 | 2002 Volvo S40

1 Answer

Asb light and brack keep flash and i have had pads changs


im pretty sure its your fluid level (steering) screw top as you stand infront of car right hand side screw top with metal connector attached

Jan 19, 2009 | 1996 Audi Cabriolet

1 Answer

Abs light on as well as brack light on the das


brake pads are the ONLY way to stop you going like 30mph+ when you hit like a wall or person or like another road user & if you do crash YOU will be totally at fault for having an unfit car. The best way to get the lights on your dash to go out is to fit new pads. The lights show that the time when the brakes WILL fail is drawing very near, it is stilll up to you to get the pads changed. You will not get any further warnings from your car prior to not being able to stop at all thus causing endangerment. You will be shocked at just how bad they were when you feel the new pads.

Jan 18, 2009 | 1999 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...