Question about 1999 Dodge Durango

1 Answer

How do I release the brake pressure so I can repair the pump?

My ABS unit is making a grinding noise when I first turn the key, keep in mind I haven't started the engine yet. How I traced it back to the ABS, I disconnected the ABS wiring and tried turn turning the key several times and no noise, I plugged it back in, noise. I'm guessing the pump is bad, but I"m not getting any abs lights or symptoms as of yet. I figure i would just replace it because it is making noise. I just needed to know how to release the pressure in the brake line so I can replace the lines for the abs. thx in advance

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 3,103 Answers

First I would disconnect the battery of the vehicle so there is no power for the pump to work..then bleed the system pressure off.. maybe by opening a line slowly..honestly I am guessing but if in doubt call the service dept and see if they can tip you also..my fortey is the older vehicles but I am game to try anyway...

Posted on Jan 19, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 275 Answers

SOURCE: 1995 Doge Dakota 3.9 v6 electrical issues

it sounds like you have a major electrical problem check all the fuses and look for any burned wires under the hood

Posted on Nov 13, 2008

ourhowse
  • 2007 Answers

SOURCE: no brakes, relaced rear brake shoes. abs, and brake lights still

Replace master cylinder.

Posted on Jun 19, 2009

  • 634 Answers

SOURCE: ABS and Brake light stay on plus pedal is soft after tight turn

sounds like you have low brake fluid pressure and the pressure sensor is turning on warning lights saying there is low pressure and also pedal going to floor indicate this, sounds like master brake cylinder is worn out/broke and needs replace ment

Posted on Jul 07, 2009

  • 12650 Answers

SOURCE: 2000 Dodge Durango 4.7 ABS, BRAKE, ENGINE light on

check fuses and relay for ur abs- possible bad relay or abs unit -have vehicle scanned some auto stores such as auto zone /advanced auto do scan for free ur trouble code(s)will give u a place to start

Posted on Oct 27, 2009

  • 151 Answers

SOURCE: 2001.5 Dodge Ram Diesel 2500 4x4 Brake Pedal drops to floor

It sounds like you have a bad mastercylinder cause when you panic brake it doesn't have time to bleed through the valve in the cylinder but under normal braking your foot is on pedal longer in turn giving the fluid time to bypass the valve in the mastercylinder in turn the pedal going to the floor.

Posted on Apr 21, 2010

Testimonial: "thnx"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 caravan 3.3 no abs brakes. I have replaced a bad master cylinder and all 4 rusted brake lines. The ABS brake warning light is not on. The van does not pull to one side.


Something is wrong with your statement
it is a 99 caravan 3.3 no abs , then you are on about abs light pump etc
the abs pump only works when the master cylinder is under pressure and that pressure is suddenly reduced by the sensor reading a locked wheel and a valve is opened to release line pressure to that wheel As soon as that wheel starts to turn, the valve closes
while the wheel is stopped and that valve is open , the abs pump kicks in to maintain line pressure otherwise the brake pedal would go to the floor
master cylinders work through a. abs unit and not because of it so if the master cylinder becomes faulty, the abs pump will not operate until a wheel stops turning as there is no line pressure to stop a wheel turning
the abs light may not be on because there is nothing to operate the system to put it on

Apr 30, 2016 | Cars & Trucks

1 Answer

What does it mean when stabilitrak and abs light comes on. Once this happen a few minutes later when I brake it makes a grinding noise.


Same as with ALL vehicle problems---
when you have a check engine light on

You stop using it
Check for OBD Codes
Diagnose your codes
Component test-- to find a problem
Make the repair

With or without codes-- you can Google
ABS Braking Systems,Trac Control & many other
abs add-ons-- to learn about them

What about reading your owners manual !!

Fail to see how using a vehicle with
brakes grinding, would be safe

Brakes have to come apart once a year
when you have no problems

Aug 13, 2014 | Cars & Trucks

1 Answer

91 Buick park avenue abs light. This happened after my friend was driving down the freeway and his tire blew. Now it just blew the rubber off and he was able to drive t off the freeway on the belts. And...


ABS LIGHT AND MODULE TROUBLESHOOTING:



Anti lock brake system light comes up when there is issue with car brake systems. It can be low brake fluid or faulty ABS fuse or its issue with brake system or assembly. Your vehicles brake system needs inspection.


To troubleshoot these issues, I suggest you to refer the help links provided below. There are direct links with accurate solution, for these specific issues.


Click the link below and follow the procedure: ------


All types of ABS LIGHT / brake problems and repairs

http://howtobyme.blogspot.com/2011/11/abs-and-service-light-comes-on.html

-------------------


ABS light stays on but brakes work fine?

http://howtobyme.blogspot.com/2011/11/abs-light-stays-on-but-brakes-work-fine.html

----------------

VCS and ABS lights go on and off intermittently on Lexus?

http://howtobyme.blogspot.com/2011/11/vcs-and-abs-lights-go-on-and-off.html

-------------

The ABS and Traction Control Lights stays ON dash of car?

http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

-------------

ABS & Brake lights warning indicator steady on dash and speedometer not working for Dodge Ram?

http://howtobyme.blogspot.com/2011/11/abs-brake-lights-warning-indicator.html

-----------------------

Battery Light and ABS Light on Dash

http://whoisbyme.blogspot.in/2012/07/battery-light-and-abs-light-on-dash.html

-------------

Sometimes ABS light comes on while Driving?

http://howtobyme.blogspot.com/2011/12/sometimes-abs-light-comes-on-while.html

-----------

How Anti-Lock Brakes Work?

http://technoanswers.blogspot.com/2011/11/how-anti-lock-brakes-work.html

-------------

Brake System Troubleshooting?

http://technoanswers.blogspot.com/2011/11/brake-system-troubleshooting.html

-------------

Anti-lock brake light stays on all the time?

http://technoanswers.blogspot.com/2012/01/anti-lock-brake-light-stays-on-all-time.html

-------------------

ABS light comes on and Car makes Grinding noise?

http://repairhelpcenter.blogspot.com/2012/01/abs-light-comes-on-and-car-makes.html

---------------

ABS trouble codes for all models?

http://repairhelpcenter.blogspot.com/2011/11/abs-trouble-codes-for-all-1994-00-acura.html
------------

2008 Toyota Highlander: ABS warning light Blinking and OBD Error codes Coming?

http://technoanswers.blogspot.in/2012/05/2008-toyota-highlander-abs-warning.html

--------------

2003 Lexus ES: VSC, TRAC OFF, ABS lights ON?

http://technoanswers.blogspot.in/2012/04/2003-lexus-es-vsc-trac-off-abs-lights.html

----------------

2008 Toyota Highlander Hybrid: Warning Lights Abs, Vsc & Brake Are On?

http://technoanswers.blogspot.in/2012/04/2008-toyota-highlander-hybrid-warning.html

-------------

ABS & Brake warning lights remains steady on dash?

http://schematicsdiagram.blogspot.com/2011/12/abs-brake-warning-lights-remains-steady.html

------------

Can I drive the car without ABS fuse connected?

http://schematicsdiagram.blogspot.in/2012/02/can-i-drive-car-without-abs-fuse.html

-----------

Where is ABS/TCS module located on 2005 Cadillac Deville

http://schematicsdiagram.blogspot.com/2011/12/where-is-abstcs-module-located-on-2005.html

------------------

ABS motor keeps running?

http://schematicsdiagram.blogspot.com/2012/01/abs-motor-keeps-running.html

------------

When the car stops, abs pump turns ON?

http://howtobyme.blogspot.com/2011/12/when-car-stopsabs-pump-turns-on.html

-----------

Replacing ABS unit on Buick Century?

http://technoanswers.blogspot.in/2012/02/replacing-abs-unit-on-buick-century.html

----------------

2008 Toyota Tacoma: ABS causes Brake pedal fade?

http://technoanswers.blogspot.in/2012/04/2008-toyota-tacoma-abs-causes-brake.html

--------------

Toyota Camry: Premature ABS Actuation?

http://technoanswers.blogspot.in/2012/04/toyota-camry-premature-abs-actuation.html

-----------

How to replace ABS Modulator Control Unit on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-abs-modulator-control.html

----------------


How to replace ABS Pump Assembly on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-abs-pump-assembly-on.html

-----------


How to remove ABS Accumulator on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-remove-abs-accumulator-on-acura.html

---------


How to remove ABS Control Unit on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-remove-abs-control-unit-on-acura.html

------------

These details will help.

Thanks.

Feb 04, 2013 | Cars & Trucks

1 Answer

93 jaguar clicking sound when i press on the brake


Few latest troubleshooting help links related to these problem.
ABS light stays on but brakes work fine? http://howtobyme.blogspot.com/2011/11/abs-light-stays-on-but-brakes-work-fine.html

--------
Sometimes ABS light comes on while Driving?


http://howtobyme.blogspot.com/2011/12/sometimes-abs-light-comes-on-while.html

---------
Brake Fade Issue? http://whoisbyme.blogspot.in/2012/07/brake-fade-issue.html Brake System Troubleshooting? http://technoanswers.blogspot.com/2011/11/brake-system-troubleshooting.html Car Brake lines have no pressure? http://schematicsdiagram.blogspot.com/2011/12/car-brake-lines-have-no-pressure.html Car Brakes Dragging? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-dragging.html Car Brakes grabbing? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-grabbing.html Car Brakes Making Noise? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-making-noise.html Car Brakes Pulling? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-pulling.html Pulsating Brake Pedal? http://repairhelpcenter.blogspot.com/2011/12/pulsating-brake-pedal.html Spongy brake pedal? http://repairhelpcenter.blogspot.com/2011/12/spongy-brake-pedal.html Hard Brake Pedal? http://repairhelpcenter.blogspot.com/2011/12/hard-brake-pedal.html Fading Sinking Brake pedal? http://whoisbyme.blogspot.in/2012/06/fading-sinking-brake-pedal.html Brakes make Grinding noise? http://repairhelpcenter.blogspot.in/2012/06/toyota-corolla-brakes-make-grinding.html

----------
These will help.
thanks.

Jul 07, 2012 | 1993 Jaguar XJ6

1 Answer

Do i need to disconnect the abs system when bleeding the brakes on my chevy s10 pickup?


just disable it by turning the key off and leave it off then pump the brake pedal 40 times. this will release the pressure from the abs pump

May 09, 2010 | 2000 Chevrolet S-10

1 Answer

2006 ford escape - abs and 4wd lights on yesterday - off today - brakes checked - ok - right turn makes grinding noise with slight application of brake -


the grinding nose you heard was something rubbing on the rotor, bad brakes, caliper, after market wheels, etc. the pressure of a turn bends something enough to touch, this is produceing metal flake that attached to the magnetic sensor on the abs sending a light on because it couldn't read the tire position as it turned, it may have got blown off, washed off, but when it can read the tire again the light will go off, i would look into the grinding noise on cornering thats the cause of the problem. hope this helps

Sep 15, 2009 | 2006 Ford Escape

2 Answers

Abs and traction control lights coming on


Its the abs sensor, if you encounter an ice patch or snow you won't even be able to stop because the pedal will will push back and make the rip grind noise. If you pull the ABS fuse out, you won't have ABS but you can stop and you won't have the grind noise and back pressure for now. Its safer to not have ABS when the sensor is faulty.

Simon Atari
simonkhpa@yahoo.com

May 06, 2009 | 2004 Pontiac Grand Prix

1 Answer

Abs sensor light wont go off my 2005 polo


Your ABS systems use a combination of electronic and hydraulic systems to modulate the brakes individually to prevent them from locking up. ANTILOCK systems consist of wheel speed sensors, a hydraulic control unit (HCU), and an electronic control unit (ECU). Because of how complex the system is your computer does a self-test. If the check is successful, the ANTILOCK and BRAKE lights will go out within a few seconds. If one of the component of the ABS system fails to pass one or both lights will remain lit. One or both warning lights may also come on while driving, also indicating a problem. If just the ANTILOCK warning light comes on, some ABS component has failed, but the car still has hydraulic brakes. The grinding noise could the the ABS pump or your brake pads could to worn to the metal backing and grinding against the brake rotors. I recommend a inspection soon for your safety.

Mar 04, 2009 | Audi S4 Cars & Trucks

2 Answers

ABS Light


I would not ignore this problem. Some damage has been caused to your braking system, i doubt if is is as simple as resetting the abs sensor. You should have the wheels removed and the suspension and braking systems fully checked over either by yourself or a competent mechanic .as the grinding sound could be a symptom of a serious safety hazard.

Driving on a flat could have buckled the rim or damaged the discs, steering or suspension.

Nov 03, 2008 | 1998 Volkswagen Golf

Not finding what you are looking for?
1999 Dodge Durango Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...