Question about 1998 Mercury Grand Marquis

1 Answer

How to remove my ignition control module in my 1998 grand marquise

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 14,382 Answers

Here's how to replace and here's the part.

Posted on Jan 19, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 68 Answers

SOURCE: have a 1998 grand marquise

See if you have brake lights,if you dont then you probably have a bad brake light switch.

Posted on Apr 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Any ideas why a 1998 Mercury Grand Marquis would just suddenly stop running in the middle of the highway going 55 mph and w a half tank of gas in it and now turns over but wont actually start again?


first suggestion is broken timing belt
second is failed crank shaft position sensor
third is failed cam shaft position sensor
forth is failed ignition control module
fifth is faulty ECM or power fuses to the ignition, ecm

Mar 23, 2017 | 1998 Mercury Grand Marquis

1 Answer

93 grand marquise has fuel all the way to the


The ignition module is attached to the fender well. It is about 5 inches square aluminum colored. Remove the mounting screws and isolate it with a rag or something to keep it from touching anything metal. Try starting it. If it does start you can re attach it with non metalic fasteners and plastic washers to isolate it. If it still wont start, replace the module.

Oct 01, 2014 | Cars & Trucks

1 Answer

How do you replace the ignition control module on a 2004 pontiac montana


first you have to remove 3 coils then remove connector, then remove ignition module.

Sep 22, 2013 | 2004 Pontiac Grand Am

1 Answer

Where is the radiator cap on a 1998 grand marquise


If it is not on the radiator, it is a coolant fill cap
located on the front of the motor next to the top
radiator hose

Mar 06, 2013 | Mercury Grand Marquis Cars & Trucks

1 Answer

1998 grand am keep cutting off when i push on the brake


You'll have to figure out if it is a fuel or ignition problem.
Is the check engine light on ? Have you checked for trouble codes ?
It could be a relay, the ignition module, coil, fuel pump, idle air control valve, or a list of other things.

Jul 10, 2012 | 1998 Pontiac Grand Am

1 Answer

Have a 1998 grand marquise and the shift wont go into gear.What do I look for


See if you have brake lights,if you dont then you probably have a bad brake light switch.

Apr 21, 2011 | 1998 Mercury Grand Marquis

1 Answer

Stop and TS problem


there is a flasher
.the hazard is wired to constant power so it works with the ignition off.
the turn signal works off of a switched power,to the turn switch and either the right or left turn signal.
if a bulb burns out,the light stays on steady

Jan 29, 2010 | 1998 Mercury Grand Marquis

1 Answer

How do I change an ignition coil on a V6 1997 Grand Am?


Removal Procedure
  1. Remove all the electrical connectors at the ignition control module.
  2. Note position of spark plug wires for installation
  3. Remove the spark plug wires from ignition coils.
  4. Remove the screws securing coil assemblies to ignition control module.
  5. Disconnect coils from ignition control module. Installation Procedure
    1. Install the coils to ignition control module.
    2. Install the screws and tighten to 4-5 Nm (36-44 lb. in.) .
    3. Install the fasteners securing assembly to engine and tighten to 8 Nm (70 lb. in.) .
    4. Install the spark plug wires as noted during removal.
    5. Install the electrical connectors to the ignition control module
  6. Hope this Helps !

Sep 30, 2009 | 1997 Pontiac Grand Am

Not finding what you are looking for?
1998 Mercury Grand Marquis Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...