Question about Cars & Trucks

1 Answer

Does the crankshaft censor have a power supply

Posted by on

  • mark Jan 19, 2013

    02 ford mondeo 2.0 tdci(130)

  •  Stephen
    Stephen Jan 19, 2013

    Since that model is not sold in the US I don't know the answer. You might try checking with the dealer, or re-ask the question with the make model and year included. Someone in your area may have the answer.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

Some models do, some generate their own power.
Whats the make model and year ?

Posted on Jan 19, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is a crankshaft positioning censor location on a 1989 Chevrolet celebrity 2.8 multiport fuel injection

It is located under hood, center, rear engine area back side of the engine block, it picks up its signal off the crankshaft throw. See picture below

Sep 27, 2016 | Chevrolet Cars & Trucks

1 Answer

My 1999 jeep grand cherokee keeps shutting off

Have you checked the asd relay ? What do you do to get it to start again ?

Feb 24, 2014 | Cars & Trucks

1 Answer

My fuel pump of my opel coarsa doesnt want to pump petrol and i have checked power on the socket is coming but i doent charge please help

Good day. A couple of things can cause your problem. First thing you can try is to connect a 12v supply to your fuelpump to see if its running. both positive and negative. There will be a positive supply present on the pump with ignition on. Its the negative wire thats being switched by a relay that is triggered by an electronic pulse censor. This censor works of a toothed gear on the front pulley. This censor also triggers the injectors as well as your spark. So if you have spark on the sparkplugs it means the censor is ok and that means your fuel relay is faulty. Most of the times its the fuel relay.

Jan 10, 2014 | Opel Corsa Cars & Trucks

1 Answer

Location of 04 corsa crankshaft censor

That sensor should be mounted behind the crankshaft pully outside of the timing belt cover.

Nov 28, 2011 | Cars & Trucks

4 Answers

Where is the crankshaft censor?

It is under the front crankshaft pulley.

Aug 09, 2011 | 2001 Pontiac Bonneville

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...

P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

1 Answer

IM a chevy Malibu 2003 My crankShaft Censor Keeps Burning out, 3times I have been to doctor (mechanic) they replace my sensor, Im good for a week then I burn out my crankshaft censor again and again what's...

One of two things. The sensor is being bumped or dropped before it is installed. Or the ECM has gone bad and it is putting out to much drive voltage for the sensors. I suspect that the sensor is being dropped or bumped before or during installation. These sensors are very fragile before they are put in. The sensor voltage from the ECM should be 5.0 volts +- .05 volts.

Sep 26, 2009 | 2003 Chevrolet Malibu

1 Answer

Mystery car

it sounds to me like a bad would probably have to take it to a shop for them to run a diagnosic test, that should tell you what censor.

Jun 18, 2009 | 2000 Dodge Stratus

1 Answer

How do u make sure if ur crank shaft censor is in time right

If the distributor syc is not set will cause the same problem

Apr 18, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Dodge 2500 5.7 crankshaft censor replacment

The crank sensor is located on the right or passenger side of the engine, at the back on top of the transmission bell housing. It is held in with two bolts and has a single electrical plug on it. Hope this helps and good luck.

Jan 17, 2009 | 2005 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides