Question about 1998 GMC Sierra

1 Answer

Remove fuel pump for 1998 GMC Sierra

How to remove the lines from the fuel pump

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 14,378 Answers

Here are 2 links to see how to change,so here is the first one.Here's the second one.You will need to relieve the fuel pressure first,click here to see how.Ask Autozone to borrow that special tool,they have a tool-loaner program.

Posted on Jan 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: in-the-tank fuel pump r&r

Here are instructions for replacment with a diagram of the fuel pump components my only suggestion would be instead of draining the tank and dropping the fuel tank if you unbolt the box and using a jack and and some wood lift the fuel tank side of the box this will give you access to the tank and fuel pump/ sending unit. It will save you time and the hastle of replacing the tank straps which are prone to snapping at the threads when trying to remove the nuts.If these brake you will have to replace them.

Posted on Nov 20, 2008

  • 12 Answers

SOURCE: removal of power steering pump on 1998 GMC Sierra 1500

you need a power steering pump puller the rest is simple any trouble let me know

Posted on Dec 24, 2008

dennymulford
  • 1055 Answers

SOURCE: 1998 GMC Sierra- runs rough then stalls when

had this problem on my neighbors 98 chevy truck with the same engine !!
it turnd out too be the fuel pressure regulator,you have too pull the upper intake too replace it!!

Posted on Jun 06, 2009

  • 10 Answers

SOURCE: fuel pump fuse located on 1997 gmc sierra

The fuse is actually a Relay Switch and its located in the Fuse Relay Center on the driverside of the engine compartment. The Black Box is labled Fuse Relay Center, the diagram on the cap displays which Relay is the Fuel Pump relay...the Relay switch is usually $8-$15 depending on where you shop

Posted on Jul 28, 2009

  • 12650 Answers

SOURCE: 1997 Gmc Sierra fuel pump relay has no power

check fuse and fuse panel connections

Posted on Oct 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace the fuel pump on my 2001 Saturn L200 with a 2.2 L Engine. What is the best procedure?


Fuel Pump REMOVAL & INSTALLATION 1.9L Engine To prevent excessive fuel spillage, whenever the tank is removed from the vehicle it should be no more than 1?2 full. Removal of the fuel pump module assembly requires the removal of the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel feed and return lines from the filter/pressure regulator
    • Fuel pump vapor line from the fuel tank vent pipe
    • Fuel pump module retaining ring with service tool SA9156E. A 1?2 inch breaker bar will loosen the lockring
    NOTE: To prevent bending of the sending unit float arm, lift the pump module up slightly to disengage the orientation tabs in the tank. Rotate the module 90 degrees clockwise until the fuel lines are facing the 1 o'clock position.
    • Fuel pump module from the fuel tank until the bottom of the pump module is close to the fuel tank opening
    • Tilt the pump module approximately 45 degrees to the right hand side of the tank and lift the pump from the fuel tank
    • Fuel pump to tank seal and discard it
    To install:
  4. Install or connect the following:
    • Fuel pump module into the fuel tank by orientating the float to face the right side and tilting the module approximately 45 degrees
    • Fuel pump into the tank and rotate the assembly 90 degrees counterclockwise to align the module tabs with the slots in the tank
    NOTE: The fuel pump retaining ring cannot be properly installed if the flange locator tabs are not aligned with the slots in the fuel tank.
    • Retaining lockring with tool SA9156E
    • Vapor line to the fuel tank vent pipe
    • Fuel feed and return lines to the filter/pressure regulator
    • Fuel feed, return and EVAP canister purge line in the fuel tank retaining clip
    • Fuel tank
    • Negative battery cable
  5. Start the vehicle and check for leaks, repair if necessary.
2.2L and 3.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel tank
    • Fuel lines from the fuel pump module cover
    • Fuel pump module retaining ring with a Sending Unit Wrench, J43827
    • Pull the retaining clip toward the float arm and lift up
    • Fuel pump straight up from the fuel tank
    • Fuel pump tank seal and discard the seal
    • Fuel feed line from the bottom of the fuel pump cover with Clamp Pliers J43914
    • Fuel pump electrical connector Fig. 1: Remove the fuel pump cover lockring-2.2L and 3.0L engines 9306zg57.gif
    To install:
  4. Install or connect the following:
    • Fuel pump feed line to the cover
    • Fuel pump electrical connector
    • Fuel pump to the new seal
    • Fuel pump cover lockring with tool J-43827
    • Fuel lines and wiring harness
    • Fuel tank
    • Negative battery cable
  5. Start the vehicle and check for leaks, repair if necessary.
prev.gif next.gif

Jan 29, 2011 | 2001 Saturn L-Series

1 Answer

How do you replace a fuel pump in a 1997 ford f350 crew cab


Removal & Installation 88285g11.gif

Details of the fuel pump assembly
Click to Enlarge 88285g12.gif

View of the fuel pump
Click to Enlarge

  1. Disconnect both battery ground cables.
  2. Properly relieve the fuel system pressure.
  3. Raise and safely support the vehicle securely on jackstands.

The electrical connector is located behind the fuel pump near the frame rail.

  1. Detach the fuel pump electrical connector.
  2. Remove the fuel line retaining clip and discard, then remove the fuel line from the fuel pump.
  3. Slide the clip up and off from the quick connect fitting. Insert the fuel line tool and remove the fuel pump delivery line.
  4. Unclip the brake lines from the fuel pump bracket.
  5. Loosen the pinch bolt and spread the mounting bracket.
  6. Remove the fuel pump.

To install:

  1. The installation is the reverse of the removal.

Oct 29, 2010 | 1997 Ford F350 Crew Cab

1 Answer

2005 toyota corolla. no problems yesterday..this morning it was dead. I can jump it and it turns over but it won't stay running. doesn't seem to be getting any fuel. Which fuse could be causing this...


Fuel Pump-(test for current at the fuel pump using a multimeter or test light while cranking) Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Relieve fuel system pressure.
  3. Disconnect the battery ground cable.
  4. Remove the rear seat cushion.
  5. Remove the rear floor service cover mounting screws and remove the cover (except '02-'04). toy_car_cor-02-04fuelpump2.gif

  6. Remove the butyl tape and remove the floor service cover ('02-'04).
  7. Remove the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Remove the fuel line U-clip and remove the fuel line from the fuel pump module.
  9. Squeeze the fuel vent line retainer and remove the vent line from the fuel pump module. toy_car_cor-02-04fuelpump1.gif

  10. Remove the 8 fuel pump module retainer ring mounting screws and remove the retainer ring ('02-'04).
  11. Remove the fuel pump module retainer using special tool 09808- 14020 or equivalent (except '02-'04).
  12. Remove the fuel pump module.
To Install:
  1. Install a new O-ring on the fuel tank.
  2. Install the fuel pump module into the fuel tank.
  3. Use the following procedure to install the fuel pump module retainer ring (except '02-'04). Fuel pump module installation toy_cor-05-18-1203.gif

    1. Align the notch in the fuel tank with the tab in the module.
    2. Matchmark a new retainer with the fuel tank.
    3. Using the special tool install and tighten the retainer ring 2 revolutions.
  4. Use the following procedure to install the fuel tank module retainer ring ('02-'04).
    1. Install the retainer ring on the fuel pump module.
    2. Fasten the retainer with the 8 mounting screws. Tighten 53 in lb (6 Nm).
  5. Install the vent line to the pipe until the fuel vent line connector clicks into place.
  6. Install the fuel line with the U-clip.
  7. Install the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Install the floor service cover with butyl tape ('02-'04).
  9. Install and secure the rear floor service cover with the mounting screws (except '02-'04).
  10. Install the rear seat cushion.
  11. Connect the battery ground cable.
  12. Check for fuel leaks.
prev.gif next.gif

Oct 16, 2010 | 2005 Toyota Corolla

1 Answer

How to fit a fuel pump in golf mark 3 cl


REMOVAL & INSTALLATION NOTE: On CIS systems the main fuel pump is located under the vehicle in front of the rear axle or in front of the tank on the right side. 1990–92 Cabriolet, Golf, Jetta and Fox TRANSFER PUMP
  1. Remove the rear seat and the access cover.
  2. Disconnect the wiring and hoses and unscrew the lock ring.
  3. Carefully lift out the pump and gauge sending unit assembly.
  4. When installing the assembly, use a new seal.
MAIN PUMP
  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Raise and safely support the rear or right side of the vehicle on jack stands.
  4. Disconnect the wiring from the pump. Clean any dirt away from the fuel line fitting.
  5. Use locking pliers to pinch off the fuel line from the transfer pump to the main pump. If the fuel line is metal, remove the rear seat and access panel and disconnect the line at the transfer pump.
  6. Place a pan under the pump and disconnect the fuel line fitting from the pump.
  7. Remove the retaining ring screws and slide the pump out of the reservoir. To install:
  8. Moisten the pump O-ring with a little fuel and slide it into the reservoir. Install the retaining ring screws.
  9. When connecting the fittings, use new copper washers and tighten the fittings to 15 ft. lbs. (20 Nm).
1993–99 Cabrio, Golf, and Jetta
  1. Remove the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Relieve the fuel system pressure.
  4. Remove the rear seat and the access cover.
  5. Disconnect the wiring and hoses.
  6. Remove the fuel lines from the pump.
  7. On 1993–99 Golf, Jetta and Cabrio vehicles, unscrew the fuel pump retaining ring.
  8. On all other models, remove the mounting bolts and the fuel pump.
  9. Carefully lift out the pump and gauge sending unit assembly.
  10. Empty the fuel pump into an approved container. To install:
  11. Installation is the reverse of removal. Be sure to use new sealing rings and/or gaskets.
prev.gif next.gif

Aug 19, 2010 | 1993 Volkswagen Golf

1 Answer

Fuel pump comes on some time when you turn on the ignition some times it doen't. Wait a while turn ignition back on and it will run.


The relay or fuel pump is going bad. Probably a fuel pump.

Mechanical Fuel Pump REMOVAL & INSTALLATION The fuel pump is located on the passengers side of the engine towards the front of the car. Fig. 1: Fuel system component layout — carbureted models 86835007.gif
Fig. 2: Mechanical fuel pump assembly mounting — carbureted models 86835008.gif
  1. Disconnect the negative battery cable. Remove the fuel pump cover.
  2. Clamp the fuel lines closed with fuel line clamps or equivalent, to prevent fuel from running out. Wrap a rag around the fuel lines and disconnect them from the fuel pump. NOTE: When disconnecting the fuel lines, twist and slide them off to avoid damage.
  3. Remove the fuel pump retaining bolts and remove the pump from the engine. To Install:
  4. Clean the gasket mating surfaces and using a new gasket, install the fuel pump in position on the block.
  5. Tighten the fuel pump retaining bolts to 17 ft. lbs. (24 Nm).
  6. Reconnect the fuel lines and make sure that they are tightly clamped. Do not over tighten the clamps or you will damage the hoses.
  7. Connect the negative battery cable and start the vehicle. Check for leaks at the fuel pump.

Jul 02, 2010 | 1994 Honda Civic Del Sol

3 Answers

How do you change a fuel pump and filter on a 2005 manual chevy aveo?


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat.
  4. Remove the fuel pump access cover.
  5. Disconnect the electrical connector at the fuel pump assembly.
  6. Disconnect the fuel line.
  7. Remove the fuel pump assembly clip.
  8. Remove the fuel pump assembly from the tank.
  9. Remove and discard the gasket.

To install:
  1. Clean the gasket mating surface on the fuel tank.
  2. Position the new gasket in place.
  3. Install the fuel pump into the fuel tank in the same location as removed for ease of line and connector installation.
  4. Install the fuel pump assembly clip.
  5. Connect the fuel pump assembly connector.
  6. Install the fuel pump line.
  7. Install the fuel pump access cover.
  8. Install the EF10 fuse.
  9. Connect the negative battery cable.
  10. Perform an operational check of the fuel pump.
  11. Install the rear seat.

Mar 06, 2010 | 2005 Chevrolet Aveo

1 Answer

Fuel pump removal and instalation


jack car up on lift, next is to dissconect lines to tank, all lines the fuel line and the evap line, dissconnect electrical connector to pump asm, when removing fuel lines wear safty glasses there may be a little prease in lines,nexy support tank,if it has a drain plug then drain the gas out,remove the filler neck from tank,remove the straps that hold tank lower the tank, remove fuel pump asm, lock ring, then remove pump asm, reverse instruction to install new pump asm, hope this helps.

Mar 02, 2010 | 2003 Chrysler PT Cruiser

1 Answer

How do I change a fuel pump on my 1995 Ford F350 7.3 2WD Power Stroke Diesel Do I have to worry about the timing eccentric? How and what do I rotate?


Hi, I hope this helps...

1994-96 Engines
See Figures 3 and 4



0900c15280262dd1.jpg Fig. Fig. 3: Details of the fuel pump assembly-1994-96 diesel engine



0900c15280262dd2.jpg Fig. Fig. 4: View of the fuel pump-1994-96 diesel engine
  1. Remove the turbocharger assembly.
  2. Remove the fuel line banjo bolt at the pump.
  3. Remove the fuel line fittings at the rear of the cylinder heads.
  4. Remove the fuel lines assembly.
  5. Loosen the two hose clamps at the fuel pump fittings.
  6. Disconnect the water drain hose at the fuel filter.
  7. Disconnect the filter and position it forward.
  8. Remove the fuel pump retaining bolts, then lift the pump out of the crankcase bore.
  9. Remove the fuel pump tappet from the crankcase bore.

To install:
  1. Rotate the engine so the fuel pump eccentric is on the base circle.
  2. Install the fuel pump tappet in the base of the fuel pump.
  3. Replace the O-ring on the fuel pump base.
  4. Install the fuel pump and bolt it in place.
  5. Install the fuel filter and connect the water drain hose.
  6. Connect the two fuel hoses at the front of the fuel pump.
  7. Tighten the fuel line clamps and install the fuel filter retaining bolts.
  8. Install the fuel line assembly and new seal rings at the rear of the pump.
  9. Loosely install the fuel line fittings at the rear of the cylinder heads.
  10. Install the fuel line banjo fitting at the pump. Tighten the fitting to 40 ft. lbs. (54 Nm).
  11. Tighten the fuel line fittings.
  12. Install the turbocharger assembly.

Oct 13, 2009 | 1995 Ford F350

1 Answer

My Toyota Sienna keeps stallling


If the car stalling then the owner of the car should check on the fuel pump assembly. prepare the tools and equipment in servicing the fuel pump,the fuel lines and the fuel filters.In the fuel pump you have to locate the fuel pump,disconnect fuel lines from the fuel pump,remove fuel pump from the engine,dis-assemble fuel pump, check the diaphram for defect , replace defective parts,assemble and install the fuel pump.
In checking the fuel lines : prepare the tools or equipment in servicing the fuel lines .So that the fuel will flow freely and no abstraction within the fuel lines.locate the the fuel lines ,visual inspection on dual line for leakage, disconnect lines at fuel pump and fuel tank .use compress air to remove sediment on fuel lines,re-install fuel lines to the unit.
the fuel filters :prepare the equipment or tools in checking the fuel filters that is going to be used.So that when fuel filters is removed ,no fuel will spill on the vehicle and no parts are lost or broken.Locate fuel filter,disconnect lines at fuel filter ,observe safety practices ,If the fuel filter is dirty then you have to clean it but if it is worn out and not anymore to be used then install new fuel filter.

Sep 24, 2009 | 2008 Toyota Sienna

1 Answer

INSTRUCTIONS TO INSTALL FUEL PUMP ON 1989 CORVETTE


REMOVAL
  1. Relieve fuel system pressure.
  2. Disconnect battery ground cable.
  3. Remove fuel filler door.
  4. Remove fuel cap.
  5. Remove fuel tank filler neck housing and disconnect drain hose.
  6. Remove screws attaching fuel meter/fuel pump to tank.
  7. Disconnect fuel lines, fuel vapor line and electrical connector.
  8. Remove fuel meter/fuel pump and gasket.
  9. Replace fuel pump.
INSTALLATION
  1. Reverse procedure to install.

Jul 27, 2009 | 1989 Chevrolet Corvette

Not finding what you are looking for?
1998 GMC Sierra Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...