Question about 1998 Volvo S70

1 Answer

Where is the camshaft relay located on a1998 s70 volvo and the number 2 spark plug is missing, what the problem

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Volvo Expert
  • 496 Answers

The Cam Relay will be at the Driver side end of the exhaust cam. You will need to remove the upper torque mount to get to it.

Posted on Jan 28, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: volvo s70 radio code

what is the radio code for 1998 vovlo s70

Posted on Mar 06, 2009

motor1258
  • 6674 Answers

SOURCE: spark plug order mixed up, Do you know correct order?

firing order is 1,3,4,2. Clockwise. #1 on distributor cap is closest to front vehicle. 4 is straight behind it. 3 is to left , 2 is to right.
Standing in front of vehicle.

Posted on Apr 25, 2009

roy7777
  • 109 Answers

SOURCE: Camshaft Position Sensor Location on s70 Turbo

IT IS LOCATED ON THE BACK OF ENGINE ON DRIVERS SIDE NEAR O2 SENSOR NEAR EXHAUST AND HAS 2 TORX SCREWS THAT HOLD IT IN PLACE NEAR ENGINE BRACKET ON T-5 2.3 TURBO

Posted on May 14, 2009

roy7777
  • 109 Answers

SOURCE: installation instructions/diagram for 1998 volvo s70 starter

IT is very easy get all of the intake ducts out of the way to get access to the starter motortakk off rubber boot and first disconnect neg battery terminal next unbolt two bolts that hold starter and the 3 wires and ground terminal from starter (i have a 14 millimeter wrench that i cuit in half to make removal easier) and you should be all-set

Posted on May 31, 2009

  • 14036 Answers

SOURCE: volvo s70 heater core

FIRST OF ALL YOU NEED A HAYNES OR CHILTON REPAIR MANUAL.IT WILL TELL YOU HOW TO GET TO HEATER CORE.AND YOU NEED TOOL NO.155 8957 DISCONNECT THE HEATER HOSES FROM HEATER CORE.AND YOU NEED A TORX 20 SCREW DRIVER TO REMOVE SOUND PROOFING PANEL TO DASHBOARD SCREWS.

Posted on Oct 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does the camshaft position sensor go on a 1999 Volvo S70?


At the rear of the cylinder head on the exhaust side camshaft.

May 29, 2014 | Volvo S70 Cars & Trucks

1 Answer

Wont start


I understand you replaced the relay but not the pump, right ?
Has the fuel filter been replaced recently ? Are you sure there is gas in the tank ?
You should be able to jumper the pump relay and check fuel pressure.

Aug 17, 2012 | 1998 Volvo S70

1 Answer

Location and how to get to Spark-Plugs on Volvo 2000 GTL , I've removed both Black Plastic covers on top of engine and do not recognise anything... Please advise ... Thankx. Kelly


There are 5 ignition coils above each plug, remove the 2 bolts for each coil, pull up on the coil and you'll see the plug underneath, replace the plugs. Make sure you mark the coils before you remove them so they go back in the same place.
http://repairpal.com/volvo-s70-2000/common_problems

Oct 29, 2009 | 2000 Volvo S70

1 Answer

Need info on replacing spark plugs and wires on 1998 volvo s70 2.4 liter engine . Any special tools required? Does the cover need to be removed to access the plugs?


No special tools required. Yes you have to take off the black cover. There should be like 6 or 8 bolts on the cover. 27 torx. After you take the cover off, you will have the ignition coils on top of the spark plugs. They are bolted down with 10mm bolts. take out the 10mm bolts and pull the ignition coils out. There you will have your spark plugs open to take out. Use the OEM recomended plugs. if you get the opti spark or some othe different multi electrode you will tend to have miss fires. Good luck

Oct 15, 2009 | 1998 Volvo S70

1 Answer

I have 5 codes on my 98 s70 volvo. the codes are p0305,p0303,p0301,p0300, and p017. Needing suggestion on what I need to do in order to have this fixed. Thanks.


Try replacing the spark plugs and I HIGHLY recommend factory plugs, they run way better and last way longer. From LOTS of personal experience. Plugs are the most common cause of misfires in a Volvo

Aug 10, 2009 | 1998 Volvo S70

1 Answer

AC problems on 1998 Volvo S70


yes it uses r134 a port located on left side top of car front view by the window washer fluid plug is blck unscrew plug add r134a while car is on and ac is on

Jun 21, 2009 | 1998 Volvo S70

2 Answers

Camshaft Position Sensor Location on s70 Turbo


IT IS LOCATED ON THE BACK OF ENGINE ON DRIVERS SIDE NEAR O2 SENSOR NEAR EXHAUST AND HAS 2 TORX SCREWS THAT HOLD IT IN PLACE NEAR ENGINE BRACKET ON T-5 2.3 TURBO

Jun 10, 2008 | 1998 Volvo S70

Not finding what you are looking for?
1998 Volvo S70 Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...