Question about 1992 Toyota Pickup

1 Answer

Truck will not start with jumper cables or new battery. just turns over

Everything else turns on exept the motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 21,873 Answers

I am assuming you mean the engine cranks but won't start, and won't crank without being jumped. If the engine cranks without jumper cables the battery and starter are working correctly.
If the engine does not start, you need to know if you are getting spark to the plugs and fuel to the injectors, and normal compression.

Posted on Jan 18, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ourhowse
  • 2007 Answers

SOURCE: 1989 toyota truck with a new motor.Sporadically

Check the setting of the clutch safety switch on your clutch pedal.

Posted on Jul 10, 2009

dttech
  • 4803 Answers

SOURCE: My 2007 tundra went dead. The ignition won't start

There are several possibilities ranging from a defective starter, to bad cable connections, to the onboard security system locking out the starter relay, or an aftermarket accessory interfering with the starter circuit, or a locked-up/damaged engine.

I have had vehicles towed into my shop for similar complaints when the only problem was that the customer was using a cheap duplicate key that they had made at the hardware store that did not have the required computer chip in it.

I have also had vehicles towed in where the customer had replaced the battery and did not have good cable connections or forgot to connect one of the wires that was supposed to to get hooked-up to the battery connector.

Then there are the questions: Are you getting any kind of "clicking" noises when turning the key or is it completely dead? If it is clicking, WHAT is clicking? Is it the starter motor itself that you hear or just the starter motor relay? Do you have battery power at the starter "S" terminal when turning the key? If not, is the transmission selector in "PARK"? Does the shift indicator on the dash indicate that the transmission range sensor is in "PARK"? (possible defective transmission range sensor) Are there any fault codes stored in ANY of the modules connected to your onboard computer network?

It is really hard to say without being able to see the truck.

Posted on Mar 18, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dead battery, used jumpers. Lights work dashboard lights up. Motor will not turn over


If the battery is very dead, it can take a while for the dead battery to regain enough charge to start. If you are jump starting from a jump box and not a running vehicle, there may not be enough power available to get the charge to a level that can start the vehicle. Hook up the jumpers cable to a running vehicle and allow 10-20 minutes for the battery to gain some charge. Monitor both batteries carefully during this time and should any unusual amount of heat or if smoke starts to come from either battery, shut everything down and disconnect as quickly (and safely) as possible.

Nov 14, 2016 | Cars & Trucks

1 Answer

1998 massey 1250 diesel tractor has a new battery but will not turn over. When you turn the key everything go off and does not turn the starter


Question ,was it running before this happened

If so ,try and turn the crank shaft ,if it turns then the problem is either a battery cable , check connections at battery and starter and also the ground .

If this fails , take a pair of jumper cables hook to battery with out battery cables hooked up .

Then hook ground from jumper cables to frame and positive to large stud on starter solinoid , take screw driver touch large post of starter to small post on starter solenoid if it just clicks or does nothing replace starter.

Be very careful these are large amperage's your working with ,and can be dangerous ! if not comfortable with this method then just take starter out and have it tested in town.

Oct 02, 2016 | Cars & Trucks

1 Answer

Hi i have a 1984 35 hp evinrude electric start E35RLCRR that wont start or turn over


If you are sure that all connections are clean and bright, including the battery to the ground and battery cable to the solenoid, jumper from the battery (+) to the solenoid (+). If the solenoid clicks, but motor doesn't turn over, your solenoid is bad. Try jumpering momentarily from the battery (+) to the starter (+) and that should cause the starter to rotate. If that makes your starter rotate, your solenoid is still bad. Be sure that your starter has a good ground connection

Dec 23, 2014 | Cars & Trucks

1 Answer

Starting problems


Bad Motor ground wire. you hear 1 click turn of key. Easy test use Jumper Cable one motor and and ground post of battery. If start go buy 24in cable and ground motor to battery.

Apr 08, 2013 | 2006 Dodge Sprinter 3500

1 Answer

MY 2007 PONTIAC TORRENT ingition turns on with all the power but when trying to start the car I get nothing,My starter motor has power going to it but still nothing


May be weak battery try jumper cables.
clean both cables at battery
then have the battery load tested.
Next remove starter and connect with jumper cables.
bypass solenoid with screwdriver.
if the battery is dun down measure the alternator output.
it should run at 14.7 vdc with everything turned on.

Mar 18, 2013 | 2007 Pontiac Torrent FWD

1 Answer

92 GMC sierra pickup with a new battery, has no power, checked battery connections, even with jumper cables it still has no power


I would start with the fuseable links on the starter and the ground connections for the engine. One of the battery cables could be corroded inside under the plastic.

Aug 25, 2012 | GMC Sierra 1500 Cars & Trucks

2 Answers

Truck will not start how can i tell if its a starter or selonoid


does it spin real fast without clanging and grinding against the flywheel? if so then its probably the solenoid bad. do you have to hit the starter with a hammer then it works? it is probably bad brushes or a worn motor. eather way i think you can only get a new starter and solenoid together not sold seperate. check for bad battery cables (loose).

May 30, 2011 | 1996 Chevrolet K1500

1 Answer

The engine will not turn over and start, and the starter whines down until it starts making a clicking noise.


SOUNDS LIKE LOW VOLTAGE. TRY # 4 CABLE JUMPER CABLES LIGHT DUTY CABLES WON'T DO THE JOB. IF IT JUMP STARTS, CHECK THE ALTERNATOR. WITH MOTOR RUNNING, VOLTAGE AT THE BATTERY SHOULD READ BETWEEN 13.90 & 14.80. REMOVE JUMPER CABLES FOR THE VOLTAGE TEST. THE MOTOR MAY HAVE TO RUN FOR A FEW MINUTES FOR A TRUE VOLTAGE READING.

Jan 25, 2011 | 1998 Hyundai Tiburon

1 Answer

Cars electrical system goes completly offline, nothing will illuminate or work until I disconnect the battery. When I turn the key to start the car everything shuts down again. Has anyone heard of this...


It sounds like a Body ground problem or a shorted Battery. Try using jumper cables and connect the NEG jumper cable to a body part on the Firewall. Then see if the lights and accessories work. You can leave the Battery cables in place. If the lights work, see if the car starts.

Dirty Battery cables can also cause this problem. So can a shorted Battery, though I would think a lightbulb would work with even a shorted Battery. Everytime you disconnect the Battery you are making a new connection when you reconnect the cables. The ends should be shiny not black.

You can eliminate the shorted Battery by disconnecting your Battery cables and use the jumper cables to bypass the Battery and use another vehicle to run yours via the jumper cables. They you will know if the Battery is shorted.

Autozone and Oreillys do free tests on Batteries and will scan your car for free if you can get it there.

Sep 10, 2010 | 2002 Ford Taurus

1 Answer

My 1998 Jimmy won't start. Just got a new starter. My battery is drain, when i use the jumper cables it still won't turn over.


with a new starter, this sounds like a bad battery cable or terminal end. the easier way to figure this out w/out checking the voltage drop across a whole battery cable is to affix the jumper cables strategically to find the bad one. Put jumper (+) on batt (+) and jumper (-) directly onto a piece of unpainted engine metal and not in the way of moving parts. If it starts this way then you've got a bad ground cable. If it didn't start, put jumper (+) on the hot post of the starter solenoid (there are 2 posts, only touch the one w/ the fatter cable going to it) or on a remote jump point if equipped, and put jumper (-) to batt (-). If it now starts you need a positive battery cable, or just a battery-to-starter cable (if separate)

Sep 29, 2009 | 1998 GMC Jimmy

Not finding what you are looking for?
1992 Toyota Pickup Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...