Question about 1992 Chevrolet S-10

1 Answer

Side marker bulb

I want to know how to get to the bulb on my S10 blazer?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

I found on the three previous s 10's that i owned it can either be reached from the under neith side or i think it is easier to pull the grill

Posted on Jan 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HOW DO I CHANGE THE DOME LIGHT BULBS ON MY 1994 CHEV BLAZER S-10


OK you just simply pull on them the light is built like a fuse just pull it out
Experience 2003 s10

Dec 30, 2014 | Cars & Trucks

1 Answer

How do I replace the Side Marker bulb on my 94 Olds 88?


don't know this car specifically, but probably the socket will turn out from the back. Get under the car and look up.

Nov 17, 2014 | 1994 Oldsmobile 88

1 Answer

Both bulbs on my 2002 S10 Blazer licence plate was burned out I replased them with new bulbs and they will not come on and I have checked the fuses what could be the problem?


you need to check for power and for ground at the lightbulb socket to determine which is not contributing to power the bulb(s). If the marker lights work at the rear then suspect a broken/melted light bulb socket, broken wire, or broken/rusted ground connection. Again, check at the light bulb socket for ground on one side (black wire) and 12V (brown wire) on the other. The light socket should have terminals that actually touch the light bulb; sometimes the sockets will melt not allowing a good connection. a cheap harbor freight multimeter (VOM) will help. Right and left side use separate fuses

Jan 13, 2012 | 2002 Chevrolet Blazer

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

1 Answer

Wiring for side marker light which is positive


Grnd should be in mounting. One wire may be marker lamp, the other turn signal. ck bulb for two elements. thick short filiment is turn flash and thin filiment is marker lamp. Good Luck

May 09, 2009 | 2007 Lexus LX 470

3 Answers

Replace parking/marker bulb front pass 98 Jeep Grand Cherokee


look in between the marker and headlights its a screw there screw it out

Apr 04, 2009 | 1998 Jeep Grand Cherokee

1 Answer

93 S10 left turn signals not working


Have you tried replacing the flasher? You'd think neither side would blink if the flasher was bad but I've seen this happen and it turned out to be the flasher. You could swap the signal flasher with the 4 way flasher to verify that's the problem before going out and buying one. Should be a few bucks at the parts store.

Apr 04, 2009 | 1996 Chevrolet S-10 Pickup

1 Answer

I have a blown bulb in my side marker on a 1992


go ahead and change it. Just go to the part store, tell them that your side marker bulb is blown and they will sell you a new on. Then get your screw driver and go to town.

tepfy

Jan 25, 2009 | 1992 Chevrolet S-10 Blazer

1 Answer

Replace side marker bulb


I have the same vehicle and just went through this. The best way to get to those side marker bulbs is to loosen or remove the front grille. There are several screws to remove this grille. I removed the top screws (hood opened you'll see them) and simply loosened the lower and center section screws. This enables you to pull the grille out far enough from the main headlight area, where you can then access the side marker bulb outlet.

Jan 25, 2009 | 1992 Chevrolet S-10 Blazer

4 Answers

1998 Chevy S10 pickup backup lights don't work


Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Sep 06, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...