Question about 2008 Dodge Avenger

Open Question

I have an 08 avenger i just replaced the throttle body and relearned i t but it still wont accelerate

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sleepygsx
  • 98 Answers

SOURCE: error display on my 08 dodge avenger's odometer

it means your trunk is open =) auto lingo for trunk is lid just another way to confuse people =) no biggie

Posted on Dec 11, 2008

  • 5370 Answers

SOURCE: 08 avenger factory alarm

Car not starting or turning over indicates towards multiple possibilities. It can be issue with battery or weak battery. But if battery checks out ok, then it can be starter issue or faulty alternator or problem with low fuel pressure or no spark at spark plugs due to dirty spark plugs or faulty ignition coil or injectors getting cracked or dirty and needs to be cleaned.


To confirm the problem, the basic troubleshooting is required.


Click this link below and follow the troubleshooting:------

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

---------

This will help.

Thanks.

Posted on Feb 16, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Engine idles a little high when in drive


check hoses for vacuum leaks also throttle body may need to be cleaned and or throttle body position sensor can be starting to be faulty or may require cleaning with throttle body --the following links show how to clean a throttle body look up the ones that do it in /on vehicle you dont have to remove it from vehicle
How to Clean throttle body GM 3800 throttle Body Tune Up Cable accelerator... Throttle body cleaning and idle relearn procedure

Jul 27, 2016 | 2006 Buick Lucerne CX

1 Answer

2005 ford five hundred replaced battery went into engine failsafe mode n will only idle no throttle response I replaced throttle body assembly just sits and idles


try using the scan tool to reset the ECM program
code p 2104 refers to throttle actuator control(TAC) system---forced idle mode ===causes ---wiring--TAC motor ---APP ensor--ECM
code p 2112 refers to throttle control actuatorTAC system---actuator stuck closed ===causes ---throttle body, throttle valve tight/ sticking
or TAC system--circuit malfunction===causes wiring short to positive ---short to ground ---throttle position sensor--- ECM

Feb 21, 2016 | Ford Cars & Trucks

1 Answer

After cleaning throttle body vehicle idles extremely high


Need to do a throttle position relearn !
A vehicle that had a heavily coked throttle body that has been cleaned or replaced may take several drive cycles to learn out the coking. To accelerate the process, the scan tool has the ability to reset all learned values back to zero. A new ECM will also have values set to zero.
The idle may be unstable or a DTC may set if the learned values do not match the actual airflow.

Jan 05, 2016 | 2009 Saturn Aura XR

1 Answer

How do I do a throttle body replacement relearn on a 04 isuzu ascender


The relearn is done by unhooking the battery for 30-60 minutes. With all HVAC OFF, hook the battery back up and drive your Ascender around for about 40 min or so, at this time, it will relearn. To test it, stop the vehicle put it in park and turn your AC on, if your car doesn't show signs of boggin down or trying to die on you, your relearn was done correctly. This is all assuming that your throttle body is CLEAN!!! If it's not clean, your idle will be bad and engine will try and die on you at idle when your AC or Defroster are on. Relearn should of already been done---> you always disconnect the battery when cleaning the throttle body, as to not to damage the stepper motor that moves the butterfly. To properly clean the throttle body and for best results, always remove the entire throttle body and clean BOTH sides with a sensor safe spray like Seafoam and a rag or nylon brush, you can reuse the hard plastic gasket. Hope this helps!

Oct 12, 2015 | 2004 Isuzu Ascender

1 Answer

I have a Ford F150 XL with a 4.6 W engine the floor got washed and now it boggs down on acceleration it is a 2009.I have replaced the acceleraton pedal and throttle body but still boggs down


Needs to go on a scanner. Throttle bodies have to be reset to the computer. No programming, just a relearn/procedure. I knew it was a bad idea to put the TPS on the gas pedal. Nothing under the dash is weather packed.

Mar 23, 2015 | Ford F-150 Cars & Trucks

2 Answers

How do I adjust the throttle body


The throttle bodies on most newer cars are not adjustable for its idle speed. If the Check Engine Light is on, go to the nearest auto parts store and get them to pull the error codes from your car's computer. Post the codes back here and we can give you a better answer to your question

Mar 22, 2015 | 2007 Toyota Corolla

2 Answers

How to relearn the acceleration sensor learning value


Hey...this code sets after maintaing the throttle body...this error is ABS speed sensor related...its an acceleration or deceleration error code...to clear this code... U need a profesdsional scanner to relearn the sensors...its a process called G-zero initialization...!
Am your Digimaster!

Oct 18, 2014 | Toyota RAV4 Cars & Trucks

1 Answer

How do i do a throttle body relearn on a 08 silverado 1500


Try clearing codes with hand held and let it relearn on its own ,you will have to drive it for awhile for relearn .it may not idle at first

Feb 10, 2014 | Cars & Trucks

1 Answer

The dealership said they did a throttle body service on my 08 dodge avenger, what does that mean.?


YOUR CAR MUST OF HAD A THROTLE BODY PROBLEM WITH A CODE SO THEY PROBLY REPROGRAM IT TO FIX A PROBLEM AND CLEANED IT OR THEY REPLACED IT HOPE THIS ANSWERS YOUR QUESTION IF NOT I CAN HELP MORE OK

Nov 19, 2012 | Cars & Trucks

1 Answer

Has low idle and wants to die when a/c is on when idling. Then when i accelerate, it sounds like it is shifting at high RPMs.


The low idle and wanting to stall is caused by a dirty throttle body, it needs to be cleaned thoroughly front and back sides using throttle body cleaning spray. Also while doing the cleaning, disconnect the battery to reset the computer so it will relearn to the newly cleaned throttle body.

Jul 28, 2011 | 2003 Chevrolet TrailBlazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...